Determine what is the total settlement under the footing

Assignment Help Civil Engineering
Reference no: EM13306147

A 2m x 2m footing has to carry a column load of 1000 kN. The ground water table is at a depth of 2m, and the saturated unit weight of the stiff clay layer is 21 kN/m3. Consolidation test was conducted on the undisturbed clay sample, and one increment of loading data with time is presented in the following table. At "0" time, the sample height was 2.314 cm, and the void ratio was 0.7. Perform the following tasks:

TASK 1: What is the sample height and void ratio after 24 hours?

TASK 2: What is the Compression Index Cc during this load increment?

TASK 3: What is the Coefficient of Consolidation, Cv ?

TASK 4: If the modulus of elasticity of the top sand layer is 35,000 kPa, then what is the strain in that layer after the construction of the footing?

TASK 5: What is the consolidation settlement of the clay layer due to 1000 kN load? Assume that the soil is normally consolidated.

TASK 6: What is the total settlement under the footing?

TASK 7: How long will it take for that settlement to occur?

TASK 8: How long will it take for the clay layer to settle 60% of the above settlement?

TASK 9: What is the excess pore water pressure in the clay layer right after the application of the load?

TASK 10: What is the remaining excess pore water pressure at 4 m into the clay layer after the time calculated in Task 8?

TASK 11: (a) Draw a soil element in the middle of the clay layer and show all stresses. Assume that the horizontal stress 50% of the vertical stress. (b) Draw the Mohr's Circle for this stress state. (c) Determine the pole and show all steps. (d) What are the principal stresses? (e) What is the maximum shear stress? (f) What are the stress conditions on a plane inclined at 40 degrees to the horizontal? (g) Show the stress conditions of (f) on the element drawn in (a).

Reference no: EM13306147

Questions Cloud

Target canada (retail store) should position : Target Canada (retail store) should position itself in pricing relative to it's competitors (Walmart Canada) and it's parent (Target US)? Second, how do you think Target Canada should communicate these changes to the consumer?"
Determine the smallest fprce p that should be applied : Knowing that the coefficient of static friction is 0.25 at all surfaces of contact, determine the smallest fprce P that should be applied to one of the wedges.
Obtain the speed of the rod : A rod 89 cm long moves in a plane perpendicular to a magnetic field of 510. G. The velocity of the rod is perpendicular to its length. Find the speed of the rod
Design and implement an application that computes and prints : Design and implement an application that computes and prints the mean and standard deviation of a list of integers x1 through xn. Read the value of n, as well as the integers, from the user.
Determine what is the total settlement under the footing : Consolidation test was conducted on the undisturbed clay sample, and one increment of loading data with time is presented in the following table. At "0" time, the sample height was 2.314 cm, and the void ratio was 0.7.
Management system and management reviews : 1.Management system 2.Management reviews.
Which of these two versions do you prefer and why : Redraw the ERD for this new situation using two entity types, and the redraw it again using one entity type. Which of these two versions do you prefer and why?
Through what distance does the piston drop : Suppose a monatomic ideal gas is contained within a vertical cylinder that is fitted with a movable piston. Through what distance does the piston drop
Why did you choose this way versus alternative ways : Section Number is an integer (such as 1 or 2) that distringuishes one section from another for the same course but does not uniquely identify a section. How did you model SECTION? Why did you choose this way versus alternative ways to model SECTIO..

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What proportion of the true stress is the applied stress

A 10cm long cylindrical rod of steel is elongated to become 12.1cm long by the application of a force of 10kN. 1- What is the ration of initial diameter to final diameter, assuming no net volume change

  What is overturning factor of safety for building wind load

How many floors can be added to the building while maintaining the code required overturning factor of safety of 2.0 Assume the roof supports a wind load of 4 kips and all floors below support a wind load of 8 kips.

  What is the distiniction b/n point and non point sources

what is the distiniction b/n point and non point sources of water pollution and thier varation with surface and ground water?

  Find the internal forces as the nut is rotated 1 turn

A steel bolt and nut are tightened around an aluminum sleeve. Find the internal forces as the nut is rotated 1 turn

  Determine the maximum stress on the beam

draw shear and bending moment diagrams determine the maximum stress on the beam (E=2.0E+11Pa) a simply supported beam AB is 5 m long carrying a uniform distributed load of 10kn/m over a 4m span

  How much money should timothy and tiffany deposit annually

how much money should timothy and tiffany deposit annually for 20 years in order to provide an income of $30,000 per year for the next 10 years. Assume the interest rate is a constant 4%

  Compute the percent voids in total mix and percent voids

An aggregate blend is composed of 59% coarse aggregate by weight (sp. Gr. 2.635), 35% fine aggregate (Sp. Gr. 2.710), and 5% filler (Sp. Gr. 2.748). The compacted specimen contains 6% asphalt binder

  What thickness of bc will result in same compressive stress

A second load P2 is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the post are dAB= 1.25 in, tAB= 0.5 in, dBC= 2.25 in and tBC= .375 in respectively.

  Calculate efficiency of esp required to meet federal source

A coal with 6% ash and a heating value of 13,000 Btu/lb is burned in a new power plant. Assume that 30% of the ask falls out as bottom ash in the furnace. Calculate the efficiency of ESP required to meet federal new source performance standards.

  What is the relationship between drag forces for two plates

Two different fluids flow over two identical flat plates with the same laminar free-stream velocity. Both fluids have the same viscosity, but one is twice as dense as the other. What is the relationship between the drag forces for these two plates

  Possible characteristic or property of sanstone

Give one possible characteristic or property of sanstone and of the quartzite that made you decide not to select it for your concrete project?

  Calculate the compacted cubic yards per hour with a drum

Calculate the compacted cubic yards per hour if a compactor with a 5-ft drum width travels at 3 mph over a 10-in. lift of aggregate base course with 4 passes required to meet density specifications under average operating conditions.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd