Determine the youngs modulus for a metal of the uts

Assignment Help Civil Engineering
Reference no: EM13322969

Determine the young's modulus for a metal whose elasic limit isone half of its UTS. The material has a strain of 0.002 at theelastc limit and a gauge length of 50mm. The UTS of the metal is300 MPa. The metal sample has a diameter of 20mm.

Reference no: EM13322969

Questions Cloud

Write a program to ask the user to enter 5 student names : Write a program to ask the user to enter 5 student names and their ages. Output the data from the parallel arrays.
Calculate and display their individual pay increases : They are considering a pay increase of 8%. Write a program that will prompt for and accept the current salary for each of the faculty members, then calculate and display their individual pay increases.
Determine the magnitude of the gravitational force : On earth, two parts of a space probe weigh 13500 N and 3790 N. These parts are separated by a center-to-center distance of 14.4 m, Find the magnitude of the gravitational force
Determine themax value of bending stress in the beam : A beam of rectangular cross section 300mm by 100mm sitsupright and has a moment of inertia of 225 X 10-6m4 and a max bending moment of 67.5KNm. Determine themax value of bending stress in the beam.
Determine the youngs modulus for a metal of the uts : Determine the young's modulus for a metal whose elasic limit isone half of its UTS. The material has a strain of 0.002 at theelastc limit and a gauge length of 50mm. The UTS of the metal is300 MPa.
What is the total end-to-end delay to send a packet : The distance between host A and the switch is d1. The distance between the switch and host B is d2. Assuming that the propagation speed is s and the switch uses store-and-forward packet switching.
What is daily compound rate of interest earned on account : An engineer in a developing country observes that his project bankaccount has grown from 1,600,000 to 1,769,279 (local currencyunits) in 20 days with no deposits or withdrawals being made.
What is the ground state energy of the electron : Take element Z = 80 from the periodic table. Ionize it 79 times so that there is only one electron left orbiting around the nucleus. What is the ground state energy of the electron
How many fragments are generated : Consider sending a 4800-byte IP datagram into a link that has an MTU of 820 bytes.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Projectile shot vertically upward

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  Determine location of the instantaneous center of rotation

The center of gravity G of the 20-in. club is located 12 in. from the knob. knowing that at the instant, G has a velocity of 4 ft/s upwards and the club has an angular velocity of 30 rad/s counterclockwise

  Determine the maximum stress on the beam

draw shear and bending moment diagrams determine the maximum stress on the beam (E=2.0E+11Pa) a simply supported beam AB is 5 m long carrying a uniform distributed load of 10kn/m over a 4m span

  What is the rockets acceleration in meters per square

At a certain altitude and time, a rocket's acceleration is 2.5 g. One gravity (g) is equivalent to 32.2 ft/s^2. What is the rocket's acceleration in meters per square second

  Determine the quality of the initial state

A two-phase liquid-vapor mixture of water is initially at a pressure of 10 bars. If on heating at fixed volume, the critical point is attained, determine the quality of the initial state.

  Obtain the production rates to loosen earth with a pick

What is the maximum length of trench that can excavated by hand economically rather than by a trenching machine. it cost 900.00 to transport a trenching machine to the job and back to the storage yard

  What is the density of moist air with a relative humidity

What is the density in kg/m3 of: (a) dry air at 25 degrees C and a pressure of 1,000 millibars; (b) moist air with a relative humidity of 80% at the same temperature and pressure

  What is the net upward force exerted

the pressure inside a commercial airliner is maintained at 1.00 ATM. what is the net upward force exerted on a (1.0 m)(200 cm) cabin door if the outside pressure is 0.30 ATM?

  What is the dry weight of sludge produced in kg per day

A water contains a suspended solids concentration of 10.30 mg/L.Coagulation reduce this to 1 mg/L.To accomplish this,an alum dose of 13.30 mg/L is necessary.

  Determine the pressure head required from the pump

A pump is necessary to lift water from the clear well (reservoir) at a water treatment plant to a storage tower 50-ft high and some distance away. A flow rate of 15 cubic per second (cfs) is required (68F).

  Discuss how the nec3 form of contract provides stimulus

Discuss how the NEC3 form of contract provides stimulus to good management and compare and contrast this where possible with other forms of contract.

  Determine the molar specific volume of the air

Atmospheric air is at 101 kPa (abs) and 25 degrees C. Determine (a) the density of the air (b) the molar specific volume of the air. Work out problem completely please. I already have the answers a) 1.18 kg/m^3 b) 24.5 m^3/kmol

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd