Determine the yield strength modulus of elasticity tensile

Assignment Help Mechanical Engineering
Reference no: EM13625415

In a tensile test, the starting gage length = 100 mm and the cross-sectional area = 150 mm^2. During testing, the following force and gage length data are collected: (1) 17,790 N at 100.2 mm, (2) 23,040N at103.5 mm, (3) 27,370 N at 110.5 mm, (4) 28910 N at 122.0 mm, (5) 27,480 N at 130.0 mm, (6) 20.460 N at 135.1 mm. The final data point (6) occurred immediately prior to failu. Yielding occurred at a load of 19,390 N (0.2% offset value), and the maximum load (4) was 28,960 N. (a) Plot the engineering stress strain curve. Determine the yield strength, modulus of elasticity, tensile strength, and percent elongation. Also determine the strength coefficient and the strain-hardening exponent in the flow curve equation.

Reference no: EM13625415

Questions Cloud

The flow curve for austenitic stainless steel has the : the flow curve for austenitic stainless steel has the following parameters strength coefficient 1200 mpa and
With the equipment provided in labs why do you observe only : with the equipment provided in labs why do you observe only the balmer series but not the lyman or paschen series?a the
A piping system consists of 100 ft of 2-in pipe a sudden : a piping system consists of 100 ft of 2-in pipe a sudden expansion to 3-in pipe and then 50 ft of 3-in pipe. water is
A copper wire of diameter 080 mm fails at an engineering : a copper wire of diameter 0.80 mm fails at an engineering stress 248.2 mpa. its ductility is measured as 75 reduction
Determine the yield strength modulus of elasticity tensile : in a tensile test the starting gage length 100 mm and the cross-sectional area 150 mm2. during testing the following
Water flows straight down from an open faucet the : water flows straight down from an open faucet. the cross-sectional area of the faucet is 1.2 times 10-4m2 and the speed
Liquid octane c8h18 at 25ordmc 10 atm enters a : liquid octane c8h18 at 25ordmc 1.0 atm enters a well-insulated reactor and reacts with air entering at the same
Find the work done per pound of water during the expansion : water in a piston-cylinder initially starts at t 400of and p 200 psia. the piston is heated until it final volume is
As a race car approaches a fan in the stands the fan hears : as a race car approaches a fan in the stands the fan hears the noise of the engine at 323 hz. as the race car recedes

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The water layer is at a temprature of 0 c determine the

a person with a mass of 85 kg wearing snow skis is gliding down a long slope at an angle of 15 degrees. each ski is 185

  Find out weld pressure adjustments

what would be the formula to find out weld pressure adjustments when atm inside the tube is changed?

  What is the sine wave generated by a phasor

what is the sine wave generated by a phasor of length 9, rotating with an angular velocity of 325 rad/s; and with the phase angle of 0."

  The temperature reaches 1800 k at the end of the combustion

a diesel engine has a compression ratio of 20 and a cutoff ratio of 2. air is at 95 kpa and 290 k at the beginning of

  The collar at a can freely slide in the y-direction and can

a vertical bar ed has a circular cross-section and is fixed at e. member abc is a single member that lies on the

  Fr what values of d is the system stable is there a value

the characteristic equation of a certain system is s210ds29d20 where d is a constant. a for what values of d is the

  A r-12 plant is to develop 5 tons of refrigeration the

a r-12 plant is to develop 5 tons of refrigeration. the condenser and evaporator temperature are to be 40c and -10 c

  Determine the total power in kw that is required to pump

water is pumped from a 200 m deep well into a 200 m tall water storage tank.a determine the power in kw that is

  Find the work and heat transfer for each process

Air in piston/cylinder at 200 kPa, 600K is expanded in a constant-pressure process to twice the initial volume (state 2). At this point, the piston is locked with a pin and heat is transferred to a final temperature of 600K. Find the work and heat..

  In a chain link fencing machine if we are using 2mm gi wire

in a chain link fencing machine if we are using 2mm gi wire at the feed of 10mm per second through a self centering

  A petrol engine uses 204 kg of petrolh of calorific value

a petrol engine uses 204 kg of petrolh of calorific value 43 mjkg. the thermal efficiency of the engine is 20.

  A hydraulic cylinder has a piston of cross sectional area

a hydraulic cylinder has a piston of cross sectional area 45cm2 and a constant working fluid pressure of 2.2mpa. the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd