Determine the work and heat transfer per unit mass

Assignment Help Mechanical Engineering
Reference no: EM13720665

Water, initially a saturated vapor at 150 degrees Celsius, is contained in a piston-cylinder assembly. The water undergoes a polytrophic process (n=1) to a pressure of 0.01 MPa, during which the piston moves freely in the cylinder. If the change of state is brought about by heating the water as it undergoes an internally reversible process at constant temperature, determine the work and heat transfer per unit mass, each in kJ/kg.

Reference no: EM13720665

Questions Cloud

Calculate the required control efficiency : An alcohol manufacturing facility emits air with 500 ppm ethanol. The air flows out several roof vents at a total flow rate of 1000 m³/min (at 25 ° C and 1 atm). The facility is required to collect all the vented air and route it to a bio filter to c..
Determine the true strain at the onset of necking : Assume that for a tensile test, d?t/d?t= ?t  when necking begins. Based on this condition, determine the true strain at the onset of necking? Explain carefully any assumptions made.
Determine the temperature at the exit of each turbine : Steam enters a two-stage adiabatic turbine at 8 MPa and 550ºC (State 1) and is expanded to 2 MPa (State 2) in the first stage of expansion. This steam is reheated at constant pressure to 550ºC (State 3) before entering the second stage of expansion.
What is the fracture toughness : A tensile sample of width 10mm contains an internal crack of length 0.3mm. When loaded in tension the crack suddenly propagates when the stress reaches 450 MPa. What is the fracture toughness K1c of the material of the sample? If the material has a m..
Determine the work and heat transfer per unit mass : Water, initially a saturated vapor at 150 degrees Celsius, is contained in a piston-cylinder assembly. The water undergoes a polytrophic process (n=1) to a pressure of 0.01 MPa, during which the piston moves freely in the cylinder.
Phase diagram for a new binary alloy : A “friend” asks you to construct the phase diagram for a new binary alloy of A and B. The clues are: (i) A and B are completely immiscible in each other and no solid solutions exist in the diagram, (ii) no stoichiometric compounds exist in the diagra..
Developed a device that converts heat transferred : An inventor claims to have developed a device that converts heat transferred to it at 1500 degrees Fahrenheit into work with a thermal efficiency of 70%. Heat is rejected to the 70 degree Fahrenheit surroundings. Is this possible? Why or Why not?
What is the minimum thickness of the weld : Hemispherical end caps are welded to a cylindrical main body to form a propane storage tank. The tank has an inside diameter of d1=40in. and is to be subjected to a maximum internal pressure of p=120 psi. The allowable tensile stress in the wall of t..
One dimensional wall of material : A one dimensional wall of material (Kw=10w/mk) is 50 mm thick with uniform heat generation q‘‘‘=5*10^6w/m^3. The left side is exposed to a fluid hl=500w/m^2k at 20 degree Celsius. The right side has a 10mm thick plate attached that has no heat genera..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The barometer reads 760 cm hg what is the pressure in psia

a pressure gauge reads 23.1 in hg inches of mercury vacuum i.e. -23.1 in hg gauge. the barometer reads 76.0 cm hg. what

  A propeller driveshaft is to transmit 2500 hp at 75 rpm it

a propeller driveshaft is to transmit 2500 hp at 75 rpm. it is to be made of aisi 1040 wqt 1300 steel. use a design

  Find the nozzle throat area the mach numbers before and

air flows through a convergent-divergent nozzle from a large reservoir in which the pressure and temperature are

  If height of the ramp is 3 m what is the most nearly the

a solid cylinder of mass 5 kg and radius of 0.1m is released from on a ramp and rolls without slipping. if height of

  Determine the max bending stress deflection of the board

a 200 pound man stands at the end of a 16 foot diving board point c with a pin at a and a roller located 6.695 ft away

  It is estimated that the isentropic efficiency of the

steam enters a turbine at 300 deg c and exhausts at 20 kpa. it is estimated that the isentropic efficiency of the

  A particle travels along the circular path xsup2ysup2rsup2

a particle travels along the circular path xsup2ysup2rsup2. if the y component of the particles velocity is vy2rcos2t

  Well-insulated heat exchanger is used to heat water

A well-insulated heat exchanger is used to heat water (cp = 4.18 KJ/kg*K) from 300 K to 90°C with a mass flow rate of 3 kg/s. Heat is supplied by hot oil (cp = 2.3 KJ/kg*K) that enters the heat exchanger at 200°C with a mass flow rate of 15 kg/s.

  Employing the ideal gas model for the gas determine the

an insulated cylinder is initially divided into halves by a frictionless thermally conducting piston. on one side of

  A company crates its products for shipping as shown base

a company crates its products for shipping as shown base plate with two springs holding a crate- mass suspended in

  Determine the pressure in the gas main if the pressure in

natural gas methane flows from a 33-in diameter gas main through a 1-in-diameter pipe and into the burner of a furnace

  Find a the volume flow rate of water in the jet sheet and

the nozzle shown discharges a sheet of water through a 180 degree arc. the water speed is 15 ms and the jet thickness

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd