Determine the volume fraction of fibers that will required

Assignment Help Civil Engineering
Reference no: EM13890852

In an aligned and continuous carbon fiber-reinforced nylon 6,6 composite, the fibers are to carry 98 % of a load applied in the longitudinal direction.

(a) Using the data provided, determine the volume fraction of fibers that will be required.

(b) What will be the tensile strength of this composite? Assume that the matrix stress at fiber failure is 50 MPa (7250 psi).

Reference no: EM13890852

Questions Cloud

Explain one scenario in which a projective test might used : a rationale for the use of projective or objective tests and explain why. Then explain one scenario in which a projective test might be used and one scenario in which an objective test might be used to assess personality in clinical practice and e..
A paper on globalization and alternative energy : a paper on globalization and alternative energy
Calculate the amounts and compositions of phases : Calculate the amounts and compositions of phases and constituents of steel composed of iron and 0.10% carbon just above and below the eutectoid isotherm
Drainage facility : Drainage facility: - Drainage facility is the normal or fake evacuation of surface and sub-surface water from a territory. Numerous rural soils need waste to enhance creation or to oversee water supplies
Determine the volume fraction of fibers that will required : Using the data provided, determine the volume fraction of fibers that will be required. What will be the tensile strength of this composite? Assume that the matrix stress at fiber failure is 50 MPa (7250 psi)
Estimate the amount of work that was required : The cars were loaded 6 at a time, and once all 36 cars were full, the wheel made a complete rotation at constant angular speed in about 2 min. Estimate the amount of work that was required of the machinery to rotate the passengers alone
Prepare a journal entry to close out manufacturing overhead : Calculate the overapplied or underapplied overhead for the year. Prepare a journal entry to close out the Manufacturing Overhead account into Cost of Goods Sold.
Calculate the azimuths of the remaining sides : Balance the following interior angles (angles to the right) of a five-sided closed polygon traverse using method 1 of section 10.2. if the azimuth of side AB is fixed at 122-32-16, calculate the azimuths of the remaining sides
Determine the average penetration of the pile : The design capacity of a steel pile is 250 kN. The pile is driven by a steam hammer with a manufacturer's hammer energy rating of 36 kN • m. Determine the average penetration of the pile

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the displacement of the car between 2.0s and 3.8s

The position of a car traveling between two stop signs along a straight city block is given by r=[9t-(43/2)sin(2t/5)]m, where t denotes time and 0s

  What is smallest diameter pipeline that may be used to carry

What is the smallest diameter pipeline that may be used to carry 6.3 L/s (100 gpm) of water if the flow is to be laminar

  Find what is the force of thrust in the horizontal direction

Water flows through the interior of a jet ski at 40ft^3/s. The water enters the boat at 75ft/s at an angle of 30 degrees to the water surface. The exit velocity id 85ft/s in the horizontal direction. The boat is in seawater at 60 degrees F.

  Find which is less than the maximum taxable wage base

Find an equation that expresses the relationship between the wages earned (x) and the Social Security taxes paid (y) by an employee who earns less than the maximum taxable wage base.

  Determine required cstr volume and hydraulic residence time

Phenol undergoes a first-order decay reaction in the CSTR with rate constant, k = 0.50 hr^-1. The current industrial pre-treatment permit for Phenol is 20 mg/l. The permit limitation may be changed, either higher or lower, in the future.

  Determine the dimension of this proposed footing

A proposed square footing carrying a total load of 500 kips is to be constructed on a uniform thick deposit of dense cohesionless soil. The soil's unit weight is 135 pcf, and its angle of internal friction is 38 degrees.

  Determine the max rimpull of the tractor in each gear

A pneumatic-tired tractor with a 354 - hp engine has a maximum speed of 3.6 mph in 1st gear. Determine the max. rimpull of the tractor in each gear if the engine effieicency is 91%.

  Design a cantilever slab to carry a uniform load

Design a 3-meter cantilever slab to carry a uniform total dead load of 8.2KN/m2 and a concentrated live load at the free end of 30 KN/m. f'c=28Mpa fy=420Mpa.

  What is force of water on spillway whose upstream is given

What is the force of the water on a spillway whose upstream depth is 1.2m and whose downstream depth is 0.2m. The width of the spillway is 3m.

  What would the aquifer specific storage be for the porosity

A confined aquifer has a specific storage of 2.5 * 10^-6 /m . The porosity is .20 and the water compressibility is 5 * 10-10/Pa.For the aquifer skeleton compressibility you just calculated, what would the aquifer specific storage be if porosity were ..

  What will be the monthly power bill at electricity costs

Water is pumped 9 mi from a reservoir at elevation 100 ft to a second reservoir at elevation 210 ft. The pipeline connecting the reservoirs has a 54-in diameter. It is concrete and has an absolute roughness of 0.003.

  Calculate the elastic recovery

A 10-mm diameter bar of 1040 carbon steel is subjected to a tensile load of 50,000 N, taking it beyond its yield point. Calculate the elastic recovery (or strain) that would occur upon removal of the tensile load.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd