Determine the velocity and position of point a at time t

Assignment Help Civil Engineering
Reference no: EM13300625

The acceleration of point A is defined by the relation a = -1.08sin kt - 1.44 cos kt, where a and t are expressed in m/s^2 and seconds, respectively, and k = 3 rad/s. knowing that x = 0.16 m and v = 0.36 m/s when t = 0, determine the velocity and position of point A when t = 0.5 s

Reference no: EM13300625

Questions Cloud

Explain titration of the lead and zinc in the aliquot : Thiosulfate was used to mask the copper in a 20.00 mL aliquot. Titration of the lead and zinc in this aliquot required 34.06 mL of the EDTA solution.
What is the rate of return on your savings : Today completes your 17th year of saving and you now have $6,528.91 in this account. What is the rate of return on your savings?
Which one of the following accurately defines a perpetuity : Which one of the following accurately defines a perpetuity?
Which one of the following statements is correct concerning : Which one of the following statements is correct concerning these two annuities?
Determine the velocity and position of point a at time t : The acceleration of point A is defined by the relation a = -1.08sin kt - 1.44 cos kt, where a and t are expressed in m/s^2 and seconds, respectively, and k = 3 rad/s. knowing that x = 0.16 m and v = 0.36 m/s when t = 0
How much will the firm net from the sale : The firm's marginal tax rate is 38%. The entire cost of the system was financed with proceeds from the sale of nine-year BB-rated corporate bonds with a $1000 par value and 6.585% annual coupon. The current yield to maturity on these bonds is 7.08..
Determine maximum and minimum values of x displacement : a= -10 (1/sec^2 ) x where x is the displacement of the mass in meters. If the initial position is -1 m and the initial velocity is +1 m/sec, find: (i) the velocity when x = 0 for the first time and (ii) the maximum and minimum values of x.
Define titration of the excess unreacted edta required : A 50.0 mL sample containing Cd2 and Mn2 was treated with 69.6 mL of 0.0600 M EDTA. Titration of the excess unreacted EDTA required 11.9 mL of 0.0220 M Ca2
Find how high will the other ball go after the collision : A 6.00 kg ball is dropped from a height of 11.0m above one end of a uniform bar that pivots at its center. The bar has mass 7.50kg, How high will the other ball go after the collision

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Find summer values for oxygen tranfer-hp and airflow rate

A fine-bubble aeration basin has a flow of 21.5 mgd, an influent BOD of 180 mg/l, 31 mg/l of mmonia, and effluent of 10 mg/l. During the winter, the wastewater temperature of 14.8 degrees C does not nitrify.

  Find pipe diameter if the pressure drop is pa per m of pipe

air flows through a horizontal iron tube (e=0.15m) at Q=5.7x10-2 m3/s. find the pipe diameter if the pressure drop is 3.5kPa per 30.5m of pipe. air density = 1.23kh/m3 dynamic vicosity = 1.79 x 10-5 N.s/m2)

  How many cubic yards of soil must be excavated from pit

The soil will be excavated from the borrow pit, moistened to increase the water content to 13.5% (assume i will not change the volume of solid mass) and then compacted to a final dry unit weight of 118 pcf.

  Will the vc meet minimum ssd standards if speeds limited

A particular crest vertical curve (VC) on US 280 at Shelton Mill Rd has long been criticized as being unsafe. Its length is 400 feet. The prevailing speed on the crest VC is 50 mph. In its present condition, its tangent grades are G1=2 percent and..

  Find what is angle aplha of slope for open rectangular tank

An open rectangular tank contains water up to about half its depth. this tank accerlerates at a=2.2m/s2 up a slope of alpha, which causes the free water surface to form an angle theta with the horizontal plane. what is angle aplha of the slope

  Determine what is the balance delay for the solution

A proposal has been submitted to replace a group of assembly workers, each working individually, with an assembly line. The following table gives the individual work elements. The demand rate for this job is 1600 units/week (assume 40h/week)

  Compare total reactor volume require to remove the substance

Compare the total reactor volume required for 90% removal of a substance that decays according to first-order kinetics with a rate constant of 0.05 day -1 in a CM system that contains a single reactor against a system that contains three CM reacto..

  Estimate the storage change for the lake during the month

A lake with a surface area of 1050 acres was monitored over a period of time. During a one month period, the inflow was 33 cfs, the outflow was 27 cfs, and a 1.5 in seepage loss was measured.

  How much of a reduction in the automobile emission

How much of a reduction in the automobile emission rate would be required to achieve the maximum eight-hour average NAAQS for CO at steady state 9ppmv (10.3 mg/m3)?

  How to determine the diameter of a drilled shaft pile

Using 1630.56 kN as the ultimate capacity determine the diameter of a drilled shaft pile that would have the same ultimate capacity and depth embedment (11.5 m) using the FHWA method. Neglect shaft resistance. Use a F.S. of 2

  Calculate the maximum length

The elevation of the lowest bottom of the structure is at 1470 feet. Calculate the maximum length (feet) of the parabolic curve required to meet the given conditions.

  How fast is the reservoir surface dropping

The flow out of a reservoir is 2 L/s. The reservoir surface is 5 m x 5 m. How fast is the reservoir surface dropping?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd