Determine the tooth numbers and nominal center distance

Assignment Help Mechanical Engineering
Reference no: EM131392835

Figure P9-4a shows a reverted clock train. Design it using 25° nominal pressure angle gears of 24 Pd having between 12 and 150 teeth. Determine the tooth numbers and nominal center distance. If the center distance has a manufacturing tolerance of ± 0.006 in, what will the pressure angle and backlash at the minute hand be at each extreme of the tolerance?

1477_0c695c47-0fe4-4a22-836b-016115f96e42.png

Reference no: EM131392835

Questions Cloud

A problem with cost-benefit analysis : A problem with Cost-Benefit Analysis is that. The role of the government as a provider of health care. Two events that were most effective in bringing about licensure of physicians were
Find the intensity of the radiation beam at the focus : A 10-W argon laser has a beam diameter of 1.5 cm. If focused to a 1-mm diameter, find the intensity of the radiation beam at the focus.
Identify a topic of interest for which argument of different : Descriptions "describe"-they depict the "what is" of a statement. Prescriptions "prescribe"-they express the "what ought to be" of a statement. When approaching controversial or emotionally charged subjects, critical thinkers are mindful of the di..
Construct a graph of sensor resistance versus distance : The source has 75 mW of power, 2 mr divergence, and a 0.5-cm exit radius. Construct a graph of sensor resistance versus distance from 0 to 2.5 m.
Determine the tooth numbers and nominal center distance : Determine the tooth numbers and nominal center distance. If the center distance has a manufacturing tolerance of ± 0.006 in, what will the pressure angle and backlash at the minute hand be at each extreme of the tolerance?
Converge to either the high or low-level equilibrium : In a graph show an example of a Multiple Equilibrium Poverty Trap with one equilibrium at a low-level of well-being and one at a high-level of well-being and an unstable critical threshold around which one will be converge to either the high or low-l..
What is the readout error : Design a system using the photoconductive cell in Figure to measure and display light intensity. Make the design such that 20 to produces an output of 0.2 to 1.0 V. What is the readout error when the intensity is 60 mWcm2?
Find the arrangement that gives the smallest error : Determine all possible two-stage compound gear combinations that will give an approximation to 3π/2. Limit tooth numbers to between 20 and 100. Determine the arrangement that gives the smallest error.
Determine which costing method that used to record inventory : Determine which costing method (Last In First Out [LIFO], First In First Out [FIFO], or weighted average cost) that is used to record inventory by your selected company.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the total horizontal shear

The pressure is positive on the windward side of the hut and is negative on the leeward side. Determine the total horizontal shear Q on the foundation per unit length of roof mea- sured normal to the paper.

  Calculate the head of the crest of the model for the maximum

An ogee spillway of a gravity dam is to be modeled using water. The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet. Using a model scale of 1:10..

  Will the shell rise or sink when the supports are removed

a spherical shell of steel that is 2 m in diameter and 1 cm thick is supported in water below the free surface at

  The volumetric flow rate at the exit of the pipe

Carbon dioxide gas enters a pipe at 3 MPa and 500 K at a rate of 2 kg/s. CO2 is cooled at constant pressure as it flows in the pipe and the temperature of CO2 drops to 450 K at the exit.

  It is known that the highest point of the siphon tube is 11

a group of students is developing a plan to deliver water from a lake to a downhill village. the students plan to use a

  Assuming that both the turbine and the pump are isentropic

consider a reheat cycle with steam leaving the boiler and entering the turbine at 4 mpa and 400 c . after expanded in

  Determine the tangential force

Determine the tangential force F and the normal force N acting on the collar when u. = 45°, if the force F maintains a constant angular motion u = 2 rad>s.

  Fnd the compressibility factor using a the generalized

1 given water vapor at 200 bar and 470oc.find the compressibility factor using a the generalized compressibility chart

  A 3000-lb car accelerates under constant power from 60

a 3000-lb car accelerates under constant power from 60 mileh to 90 mileh on a 0.25 mile straight level test track.

  Calculate the steady rate of entropy production samp kjks

draw a complete schematic diagram show arrows symbols amp numeric values for each w amp amp q amp . consider the steady

  What is empowerment and why is it important in tqm

What does customer focus mean? Who is the customer?

  What is the maximum roughness height allowable for the pipe

The tank-pipe system of Fig. P6.49 is to deliver at least 11 m3 /h of water at 20°C to the reservoir. What is the maximum roughness height allowable for the pipe?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd