Determine the time taken for the flux to change

Assignment Help Electrical Engineering
Reference no: EM131340274

1. The flux linking a 600 turn coil changes uniformly from 100 mWb to 50 mWb in a time of 85 ms. Calculate the average emf induced in the coil.

2. An average emf of 350 V is induced in a 1000 turn coil when the flux linking it changes by 200 Wb. Determine the time taken for the flux to change.

Reference no: EM131340274

Questions Cloud

What is the yield to maturity on the given bond : Elizabeth Cherry has a bond that has 10 years to maturity, a face value of $1,000, an 8% interest rate, and a market price of $1,200. What is the yield-to-maturity on this bond?
How you would set up present value calculation in your case : Econ104- Explain and show your calculations (using the template at the end of this assignment) of how you would set up the present value calculation in your uncle's case.
Assessment incorporates multiple elements : This assessment incorporates multiple elements. Be sure to thoroughly address each before submitting the assessment.
What is the industry average price earnings ratio : What is the industry average price-earnings ratio? What is Ragan's price-earnings ratio? Comment on any differences and explain why they may exist.
Determine the time taken for the flux to change : An average emf of 350 V is induced in a 1000 turn coil when the flux linking it changes by 200 Wb. Determine the time taken for the flux to change.
Measure credit risk capital adequetly component of pillar : Define credit risk? What approaches may be used to measure the credit risk capital adequetly component of pillar 1? Using the standardised approach to credit risk, explain how a commercial bank will use this method to calculate its minimum capital ..
Identify the type of software or management tools : 1. Conduct research using the Internet and identify the type of software or management tools that you would utilize to help with each of the major steps in developing the plan. Summarize the software/suite selected and identify its key capabilitie..
Managing a diverse workforce : Based on your understanding of chapter 16 (Managing a Diverse Workforce), present arguments for or against workforce diversity and cite at least 3 outside sources to support your view points and conclusions..... (Must be at least 3 double-spaced p..
Determine the emf induced in the coil : A coil of 2000 turns is linked by a magnetic flux of 400 μWb. Determine the emf induced in the coil when (a) this flux is reversed in 0.05 s, and (b) the flux is reduced to zero in 0.15 s.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the inductance l and capacitance c of the circuit

The bandwidth of a series resonant circuit is 400 Hz. (a) If the resonant frequency is 4000 Hz, find Q. (b) If R = 10 ohm, what is the value of XL at resonance

  Discuss the choice of slope angles if the location is at 75

Determine the panel orientation you would choose to obtain maximum energy: (a) Over the year (b) In the summer (c) In the winter Discuss your choice of slope angles if the location is at 75°N.

  Calculate the normal strain and elongation of the plate

A square plate of titanium is 12cm along the top, 12cm on the right side, and 5mm thick. A normal tensile force of 15kN is applied to the top side of the plate. A normal tensile force of 20kN is applied to the right side of the plate.

  Write a qbasic program to tabulate the voltage vc

Write a QBASIC program to tabulate the voltage vC and current iC for the network of given figure for five time constants after the switch is moved to position 1 at t = 0 s.

  Determine the dc voltages vb ve and vc with respect to

Determine the dc voltages, VB, VE, and VC, with respect to ground in Figure 3-74. Determine the voltage gain for the CE amplifier in Figure 3-74. Determine IC(sat) for Q1 and Q2 in Figure 3-43.

  What is the direction of the magnetic field

Suppose a wave propagates in the x-direction and has its electric field along the y-direction [So Ex = Ez= 0, and Ey = Ey(x,t)].

  Find the gain kp necessary to meet requirements

A proportional control system is to be used to control the wing flaps of a jet air-plane. The wind load is expected to cause as much as 600 in .lb of torque. The system should be able to keep the flaps to within 5 of the set point.

  What volume charge density should be assigned to subregion

Electrons are in random motion in a fixed region in space .During 1 sec interval, the probability of finding an electron in a subregion of volume 10^(-15) m3 is 0.23. What volume charge density , appropriate for such time durations, should be assig..

  Determine what is the value of 1 lsb referred to 3 v

Clearcly, any noise will pass straight through to the ADC subsystem, introducing measurement error. You have two choices to mitigate this: SW filtering and HW filtering. Assume the uC sample rate, Fs, is 100 Hz with 8 bit resolution.

  Produce a simple random sample of students

Decide whether these sampling methods produce a simple random sample of students from a class of 30 students. If not, explain why not.

  Find the electric field intensity and electric potential

A ring charge has charge density ρl = ksin(φ) .It is placed on the xy-plane, centered at the origin, and has a  radius of 2. (i) Find the electric field intensity E at (0, 0, h) (ii) Find the electric potential V at (0, 0, h)

  What is the magnitude of the repulsive force between

What is the magnitude of the repulsive force between

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd