Determine the temperature of propane at the end of process

Assignment Help Mechanical Engineering
Reference no: EM13717427

A quantity of propane is contained in a piston-cylinder assembly. This working fluid undergoes a process starting from an initial state of 2.0 MPa and 60oC. At the end of the process the pressure of the propane is 1.0 MPa and the specific entropy is 0.089 kJ/kgK higher than at the start of the process.

Determine the temperature of the propane at the end of the process

Reference no: EM13717427

Questions Cloud

Find the octave band sound power level : A forward - curve centrifugal fan has 32 blades and rotates at 3000 rpm. It delivers 5000 cfm of air with a static pressure of 5 in of water. Find the octave band sound power level
Calculate the power generated by the turbine in mw : The mass flow rate through a steam turbine operating under steady conditions is 100 kg/s. Steam enters the turbine at 12 MPa and 400oC. A mixture of vapour and liquid water exits the turbine at 10 kPa. At the exit state 93% of the mass of the water i..
Evaluate the average power developed by the engine : A 1.50 x 103-kg car starts from rest and accelerates uniformly to 17.3 m/s in 12.0 s. Find the average power developed by the engine
Find the initial total mechanical energy of the projectile : A 56.0-kg projectile is fired at an angle of 30.0° above the horizontal with an initial speed of 1.28 x  102 m/s from the top of a cliff 138 m above level ground, find the initial total mechanical energy of the projectile
Determine the temperature of propane at the end of process : A quantity of propane is contained in a piston-cylinder assembly. This working fluid undergoes a process starting from an initial state of 2.0 MPa and 60oC. At the end of the process the pressure of the propane is 1.0 MPa and the specific entropy is ..
Determine the length of a copper wire : Determine the length of a copper wire that has a resistance of 0.172 ohms and cross-sectional area of 7.85 x 10-5 m2. The resistivity of copper is 1.72 x 10-8 ohm•m
Estimate the velocity of the center of mass : A 2.04 kg particle has a velocity (2.09i - 2.98j) m/s, and a 2.91 kg particle has a velocity (0.92i + 5.98j) m/s. Find the velocity of the center of mass
Determine the specific work produced by the turbine : Steam flows through a turbine. The inlet stream is at 1200 KPa and 290 C. The pressure at the exit is 75 KPa. A) Determine the quality and temperature of the steam at the exit. B) Determine the specific work produced by the turbine.
What is the boiling heat transfer coefficient : Consider that you are boiling water near its critical heat flux in a pot on the stove without a lid (pressure is atmospheric). Suppose the hot burner has a surface temperature of 128 degrees Celsius. Assume a 1 square meter area. What is the boiling ..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The cylinder from a supply line until all the liquid in the

an insulated vertical piston-cylinder device initially contains 11.56 kg of water 6.94 kg of which is in vapor phase.

  Consider a cylindrical nickel wire 19 mm in diameter and 32

consider a cylindrical nickel wire 1.9 mm in diameter and 3.2 times 104 mm long. calculate its elongation when a load

  For the forgoing conditions and a fin unit width calculate

a straight fin of rectangular cross section fabricated from an aluminum alloy k 185wmk has a base thickness of t3mm and

  Determine a the change in specific entropy of the water b

water enters a condenser at a pressure of 200 kpa and a quality of 0.95. the pressure drops by 25 kpa across the

  What is the final temperature of the liquid

A liquid has a density of 500kg/m^3 and a specific heat of .02 KJ/kg*K. The Liquid fills a rigid container, that is insulated ( no heat transfer ), from a line at P=313kPa and T = 135C. What is the final temperature of the liquid when the container i..

  Two kg of a mixture having an analyis of on a mass basis of

two kg of a mixture having an analyis of on a mass basis of 30 nitrogen 40 carbon dioxide 30 oxygen is compressed

  Find how much should be cut off from free length of the

a helix compression spring is manufactured using the following parametersod1.00id.790wire dia 0.105fo 40.49 lbf

  At that instant the sing was moving up at a constant rate

determine the velocity and acceleration of a small child in a swing of length 3.5m at a time when the swing is at 30

  Calculate the change in free-energy

Calculate the change in free-energy associated with the formation of a critical spherical nucleus in pure liquid nickel that is 200 ºC under cooled. Properties of Nickel: Heat of Fusion 2660 J/cm3; Surface Energy 255x10-7 J/cm2 ; Freezing Temperatur..

  The pressure is maintained constant in the cylinder

A piston-cylinder device contains 12 kg of saturated R-134a vapor at 3.2 bars. An electric source supplies 8 A current to a resistor within the cylinder for 4 minutes and there is heat transfer of 400 kJ to the system. During these energy interaction..

  A carnot heat pump is to be used to heat a house and

a carnot heat pump is to be used to heat a house and maintain it at 25c in the winter. on a day when the average

  Calculate the following the u10050 stirling motor stirling

calculate the following the u10050 stirling motor stirling engineoverall efficiency thermal efficiency mechanical

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd