Determine the station of pt of a horizontal curve

Assignment Help Civil Engineering
Reference no: EM13305840

A horizontal curve is being designed around a pond with a tangent length of 1200 ft and central angle of 0.5211 radians. If the PI is at station 145 + 00, determine the station of PT.

Reference no: EM13305840

Questions Cloud

Determine the value of a share of dupont series : Determine the value of a share of dupont series a $4.50 cumulative preferred stock, no par, to an investor who requires a 9 percent rate of return on this security.
What is the average seepage velocity of the groundwater : If the front edge of a contaminant plume is perfectly straight, how long would it take to travel to Well 1 after first arriving (simultaneously) at Wells 2 and 3, assuming that the contaminant plume travels only half as fast as the groundwater flo..
What is the wavelength of the refracted light : Light traveling in water strikes the boundary between two mediums at an angle of 35 degrees. what is the wavelength of the refracted light traveling at 1.85x10^8m/s
How much will be in your account after 5 years : If you deposit $10,000 in a bank account that pays 10% interest annually, how much will be in your account after 5 years?
Determine the station of pt of a horizontal curve : A horizontal curve is being designed around a pond with a tangent length of 1200 ft and central angle of 0.5211 radians. If the PI is at station 145 + 00, determine the station of PT.
Why do owners prefer the design-build form of contracts : Why do owners prefer the design-build form of contracts when many of them know they can obtain better quality construction using other forms. What are the stages at which the designer will schedule design reviews.
Determine is the final image real : What focal length objective lens is required for a 3 meter length telescope which uses a 4 Power eyepiece? Is the final image real
Determine the work done in the compression process : Methane is compressed in a piston-cylinder device from initial pressure of 110 kPa and an initial temperature of 25 oC to a final pressure of 1,00 MPa. The compression process is polytropic with n = 1 .10.
What is rollins cost of preferred stock : The firm's policy is to use a risk premium of 4percentage points when using the bond-yield-plus-risk-premiummethod to find ks. Flotation costs on new common stock totals 10percent, and the firm's marginal tax rate is 40 percent.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Calculate the speed at impact on a large rock

A large rock became visible to a driver at a distance of 175 ft. Assuming a perception-reaction time of 0.8s, an initial speed of 42 mph, a coefficient of friction equal to 0.5, and a level roadway, calculate the speed at impact.

  Determine what is the change in the wires total resistance

You have two wires connected end to end. Wire 1 is copper and wire 2 is made using a special carbon conductor. Wire 1 has a resistance of 0.215 ohms/ft and is 500 ft long. Wire 2 has a resistance of 0.141 ohms/ft and is 700 ft long.

  Find contact time would be reuired for inactivating giardia

How much contact time would be reuired for inactivating Giardia cysts using the following chemicals at the concentrations and temperatures stated: a. Chlorine Dioxide, 23C, 1.0 mg/L b. Chlorine, 12C, 1.6 mg/L c. Ozone, 10C, 5 mg/L d. Chloramines, ..

  Determine the normal depth yo and critical depth yc

A 1 m diameter unfinished concrete pipe (n = 0.015) has a slope of So = 0.001 and conveys water at Q = 0.5 m3/s. Find the normal depth yo and critical depth yc.

  Construction of the embankment

Pore water pressure is to be observed during the construction of the embankment. Calculate the pore water pressure which must not be exceeded at any point in the clay layer 9 m below the surface of the embankment to ensure a shear strength of 100 ..

  Determine the allowable force f that may be applied

If the allowable shear stress in the 7/8" diameter bolt is 35 ksi, determine the allowable force F that may be applied.

  Find estimated primary consolidation settlement of structure

A compressible clay layer 10.0m thick has an initial void ratio in situ of 1.026. Tests and computations show that the final void ratio of the clay layer after construction of a structure is 0.978. Determine the estimated primary consolidation set..

  Estimate particle size will be collected with efficiency

A cyclone is designed with an inlet width (W) of 12.0 cm and has four effective turns. The inlet gas velocity is 15.0 m/s and the particle density is 1.70 g/cm3. (a) Estimate the particle size that will be collected with 50 % efficiency.

  Dimensions of an acceptable box of a largest area

A delivery company accepts only rectangular boxes the sum of whose length and girth (perimeter of a cross section) are equal to 108cm. Find the dimensions of an acceptable box of a largest area.

  Calculate max torque that can be carried by hollow section

Assume a cross-sectional medial length of 32 in. (no stretching of the sheet due to bending). If the maximum shear stress must be limited to 19 ksi, determine the maximum torque that can be carried by the hollow section

  Power developed by the force for a block

The block has a mass of 150 kg and rests on a surface for which the coefficients of static and kinetic friction are 0.5 and 0.4, respectively. If a force F = (60t^2) N, where t is in seconds, is applied to the cable, determine the power developed ..

  Description of the soil characteristics

For each of the horizons, provide a description of the soil characteristics and briefly describe the environment where you would expect to find the horizon?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd