Determine the speed of the spike just after rebounding

Assignment Help Mechanical Engineering
Reference no: EM131231725

15-11. During operation the jack hammer strikes the concrete surface with a force which is indicated in the graph. To achieve this the 2-kg spike S is fired into the surface at 90 m>s. Determine the speed of the spike just after rebounding.

15-14. A tankcar has a mass of 20 Mg and is freely rolling to the right with a speed of 0.75 m> s. If it strikes the barrier, determine the horizontal impulse needed to stop the car if the spring in the bumper B has a stiffness

(a) k S 8 (bumper is rigid), and

(b) k = 15 kN> m.

Reference no: EM131231725

Questions Cloud

Who is the current president of gallaudet : What are your thoughts on the 2nd protest? Are your thoughts the same or different toward this protest compared with the 1st protest? Be sure to give details and thoroughly explain your reasoning - your response should be substantial.
Evaluate and weigh the different components : How do graduate admissions committees evaluate and weigh the different components of the graduate admissions package - biographical statement or personal statements with your career interests and goals
Most plausible explanation for this association : According to the 2010 census, those states with an above average number of people who fail to complete high school (X) tend to have an above average number of infant deaths (Y). In other words, there is a positive association between X and Y. The mos..
Why would a person believe this is the right option : Why would a person believe this is the right option? What age do you think this person might be? What kinds of problems and successes is a person with this point of view likely to encounter during their lives?
Determine the speed of the spike just after rebounding : During operation the jack hammer strikes the concrete surface with a force which is indicated in the graph. To achieve this the 2-kg spike S is fired into the surface at 90 m>s. Determine the speed of the spike just after rebounding.
Statements about assembly line balancing : Which of the following statements about assembly line balancing is NOT correct? Which of the following statements concerning logistics service outsourcing is not true?
Write a taylor series expansion : Apply the explicit integration method for the numerical solution of the 1D Poisson equations (that includes the free carriers) by following the steps outlined below: Write a Taylor series expansion for ψ(x) around x=0, keeping the terms up to the f..
How and where young children receive aggressive scripts : Explain how and where young children receive aggressive scripts for behavior and describe the characteristics of effective strategies that change or neutralize these scripts.
Compute the mean and auto covariance functions : Let us assume that {Wt}t is a variance-one white noise, Compute the mean and auto-covariance functions of the time series {Xt}t.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Design a cam to move a follower at a constant velocity

Design a cam to move a follower at a constant velocity of 100 mm/sec for 2 sec and then return to its starting position with a total cycle time of 3 sec. Hint: Use a two-segment polynomial to describe the follower displacement.

  What is the voltage output referenced to the noise level

A microphone having an open-circuit sensitivity of -55 dB is said to have a noise level of 28 dB. For a sound level of 90 dB, what is the voltage output referenced to the noise level?

  A 3000lb car is driven down a 5 degree incline at speed of

a 3000lb car is driven down a 5 degree incline at speed of 50mph. highway with radius 400 m and speed of 90 kmh. the

  What is the energy recoverable as heat per decay in mev

An alpha-emitter, has been used as a thermal power source, as described in Table 12.2. What is the energy recoverable as heat per decay in MeV? Provide two answers, one assuming all of the energy produced is dissipated as heat, and one assuming only ..

  A four-cylinder spark ignition engine has a compression

a four-cylinder spark ignition engine has a compression ratio of 8 and each cylinder has a maximum volume of 0.6l. at

  What maximum load can the member take before buckling would

a round compression member with both ends pinned and made of aisi cold-drawn steel sy441 mpa e207 gpa is to be used in

  Define the final state inside the tank

Find the final state inside the tank, A tank contains 2kg of nitrogen at 10K with a quality of 50%.Through a volume flow meter and valve, 0.5kg is now removed while the temperature remains constant.

  The united states is currently considering standards to

the united states is currently considering standards to generate 20 of its electricity from renewable resource in the

  What is the heat dissipation per chip

If N = 120 chips attached to the outer surfaces of the heat sink maintain an approximately uniform surface temperature of T 2 = 50°C and all of the heat dissipated by the chips is assumed to be transferred to the coolant, what is the heat dissipat..

  What makes it special or stands out from other machines

What makes it special or stands out from other machines?

  What will be the approximate temperature of the alloy

Is it possible to have a copper–silver alloy that, at equilibrium, consists of a \beta phase of composition 92 wt% Ag–8 wt% Cu and also a liquid phase of composition 76 wt% Ag–24 wt% Cu? If so, what will be the approximate temperature of the alloy? I..

  Water in a piston-cylinder assembly with an initial volume

water in a piston-cylinder assembly with an initial volume of 0.01m3 has an initial temperature of 120c and an initial

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd