Determine the reactions at points a and b

Assignment Help Mechanical Engineering
Reference no: EM131384014

A spanner wrench is used to apply torque to circular shafts and other similar shapes. Such wrenches are routinely used in the setup of tools such as milling machines, lathes, and so on. The wrench makes contact with the shaft at point A, which may be assumed to be frictionless, and at B where a small pin fits into a hole in the shaft. If P = 80 N, L = 120 mm, r = 25 mm, and a = 120°, determine the reactions at points A and B.

1201_019a0c85-ead6-47ef-8159-bfae095a6024.png

Reference no: EM131384014

Questions Cloud

Find compression of the spring when block first come to rest : The block is now lifted to a height 3a/2 above the floor and released from rest. Find the compression of the spring when the block first comes to rest.
Explain what makes it a comprehensive mission statement : HSA300: A small primary care clinic has 69 employees, representing 9 different clinical professions and 12 other skills. It operates two (2) sites, one (1) of which is bigger and has the departments for medical specialists, diagnostic labs, and pa..
Determine the smallest force p : For any possible position of the handle, determine the smallest force P and the corresponding value of a that will cause the press to tip about point A.
Find speed with which the stone is projected by the catapult : A stone of mass m is placed at the center of the cord, which is pulled back a distance 3a/4 and then released from rest. Find the speed with which the stone is projected by the catapult.
Determine the reactions at points a and b : The wrench makes contact with the shaft at point A, which may be assumed to be frictionless, and at B where a small pin fits into a hole in the shaft. If P = 80 N, L = 120 mm, r = 25 mm, and a = 120°, determine the reactions at points A and B.
Evaluate the financial condition of the company : HSA525:Suggest the financial ratio that most financial analysts would use to evaluate the financial condition of the company. Provide support for your rationale.Speculate on the organization's ability to meet its financial obligations as they come ..
Is the general motion periodic : Two particles P and Q, each of mass m, are secured at the points of trisection of a light string that is stretched to tension T0 between two fixed supports a distance 3a apart.- Is the general motion periodic?
Find normal frequencies and the forms of the normal modes : A particle P of mass 3m is suspended from a fixed point O by a light inextensible string of length a.- Find the normal frequencies and the forms of the normal modes for this system.
Discuss the conducting an environmental analysis : HSA599:For all assignments assume that you are the administrator of a fictitious organization of your choice. The organization can be any type of health care organization such as a hospital, nursing home, rehabilitation center, clinic, etc.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the expected change in the natural frequency

Find the expected change in the natural frequency of the beam-machine system.

  Liquid in a tube varies with tube diameter

The capillary rise, h, of a liquid in a tube varies with tube diameter, d, gravity, g, fluid density, p, surface tension, Y, and the contact angle, B. (a) Find the dimensionless form of this statement. (b) If h = 3 [cm] in a given experiment, what wi..

  The fluid is incompressible and the flow is steady

A two-dimensional reducing bend as shown is used to control flow rate and direction of flow in a home air conditioning duct. In the reducing bend shown, there is a linear velocity profile at section (1). The flow is uniform at sections (2) and (3). T..

  An elevator is hung by a steel rope

An elevator is hung by a steel rope. The rope has a cross-sectional area of 250mm2 and a modulus of elasticity of 70 GPa. the upward acceleration when the elevator starts is 4 m/s2. the rope is 100m long and the elevator weigh 1000 kg. determine the ..

  Find the closest location d to the load

Find the closest location d to the load at which you can move the generator so that the generator is best matched to the line (that is, the reflection coefficient at the generator is minimum). Assume the phase constant on the line is known as β0.

  Drawing up a system requirements specification

Suggest how an engineer responsible for drawing up a system requirements specification might keep track of the relationships between functional and non-functional requirements.

  Find the amplitude of vibration of the absorber mass

determine the stiffness and mass of the absorber. Also find the amplitude of vibration of the absorber mass.

  What is the contsponding gravimetrk analysis

Calculate the molar man of the mixture, and the density if the temperature is 550°C and the total pressure is 1 bar

  Identify the mystery nucleus

In an elastic collision between an alpha particle and an unknown nucleus at rest, the alpha particle was deflected through a right angle and lost 40% of its energy. Identify the mystery nucleus.

  Determine the surface at which motion will impend

the surface at which motion will impend

  Determine the amount of energy dissipated in friction

A 5-kg uniform square plate is supported by two identical 1.5-kg uniform slender rods AD and BE and is released from rest in the position θ = 45°. Knowing that the angular velocity of AD as it passes through the vertical position is 5.2 rad/s, det..

  Estimate minimum fluidizing velocity for air and for water

For spherical sand particles with Dp = 0.045 inches and the density of each particle is 145 lbm/ft3, estimate the minimum fluidizing velocity for air and for water. Assume a porosity of 32 percent. You may need to rederive Equation 11.41 considering ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd