Determine the proportional limit stress the modulus

Assignment Help Civil Engineering
Reference no: EM13563766

1.A load test on a 4.5-mm-diameter by 125-mm-long magnesium alloy rod found that a tension load of 831 N caused an elastic elongation of 0.47 mm in the rod. Using this result, determine the elastic elongation that would be expected for a 16-mm-diameter rod of the same material if the rod were 1.6 m long and subjected to a tension force of 3.3 kN.

2.At the proportional limit, a 32-mm-thick by 87-mm-wide bar elongates 10.2 mm under an axial load of 532 kN. The bar is 2.4 m long. Poisson%u2019s ratio, , for the material is 0.27.

Determine a) the proportional limit stress, b) the modulus of elasticity, and c) the change in each lateral dimension (i.e., the change in the thickness and width dimensions).

Reference no: EM13563766

Questions Cloud

Determine the horizontal components of the forces necessary : A 6 foot diameter pipleine carries water at a temperature at 60F at a steady flow rate of 60 cubic feet per second. The pipeline makes a 90 degree horizontal bend.
Estimate a value of msw generation in the year 2025 : The United States Environmental Protection Agency (EPA) has published the following data for municipal solid waste generation (in millions of tons).
What percent removal efficiency may be expected under : A cyclone separator is being used to remove particulates from a gas stream. The current removal efficiency is 96% for an air flow rate through the separator equal to 18 m3/s. Due to a process change, the air flow rate is expected to increase to 22 m3..
Calculate a value of temperature that could be used : A correlation for particulate removal efficiency in an electrostatic precipitator (n) as a function of gas velocity (u) may be written in the form: n = 1 - e^-k / u.
Determine the proportional limit stress the modulus : At the proportional limit, a 32-mm-thick by 87-mm-wide bar elongates 10.2 mm under an axial load of 532 kN. The bar is 2.4 m long. Poisson%u2019s ratio, , for the material is 0.27.
Can one collector be temporarily taken out of service by : Dust is removed from the airstream of a municipal incinerator by four dust collectors operating in parallel, each handling 1/4 of the total airflow of 200 m3/min. The airstream contains 10 g/m3
Design the flexural reinforcement for this member : A rectangular concrete beam of width b = 24 inches is limited by architectual considerations to a maximum total depth of h = 16 inches. it must carry a total factored load moment of Mu = 400 ft-kips. Design the flexural reinforcement for this member,..
Calculate the emissions of sulfur dioxide : Calculate the emissions of sulfur dioxide, particulates (fly ash), and carbon dioxide per kilowatt-hour of electrical energy produced. Assume that all of the carbon in the coal is released to the atmosphere.
What is the second year book value for equipment with : What is the second year book value for equipment with an initial cost of $11,000, a salvage value of 1,000 and a recovery period of 5 yrs for A. straight line depreciation. B. Double declining balance. C. MACRS?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the change inside diameter when the gun is fired

a navel gun (E= 30,000 ksi and G = 11,600 ksi) with a bore of 16 in. develops a maximum internal pressure of 20,000 psi. Determine a. the minimum outside diameter required if the maximum tensile stress permitted in the gun barrel is 36,000 psi.

  At which the driver could apply the brakes and still stop

The road is in good, dry conditions until 160 ft before the stalled car where it is wet and stays wet for the remaining length. What is the minimum distance from the stalled car at which the driver could apply the brakes and still stop before hitt..

  Determine the tensions in the cables and the reactions at a

The force F is acting on the boom ABC at C points in the direction of the unit vector 0.7071i-0.7071j and its magnitude is 10kN. The boom is supported by a ball and socket at A and cables BD and BE.

  Determine the elevation and stationing of the low point

A horizontal curve on a single-lane highway has its PC at station 124+10 and its PI at station 131+40. The curve has a superelevation of 0.06 ft/ft and is designed for 70 mi/h. What is the station of the PT?

  What would be the concentration of pollutant in the effluent

A lagoon with volume 1,200 m^3 has been receiving a steady flow of a conservative waste at a rate of 100 m^3/day for a long enough time to assume that steady-state conditions apply. the waste entering the lagoon has a concentration of 10 mg/L. Assumi..

  What is the major head loss in a coarse concrete pipe with

What is the major head loss in a coarse concrete pipe with a diamter of 1ft that is 100 ft long. Water flows at a rate of 20 ft^3/s (viscosity of water = 2.344x10^-5 lbfs/ft^2, density of water = 1.94 slugs/ft^3) 1inch = 25.4mm

  Determine the carburizing time necessary to achieve

Determine the carburizing time necessary to achieve a carbon concentration of 0.35 wt% at a position 2 mm into an iron-carbon alloy that initially contains 0.10 wt% C.

  Suggest a hen managentment strategy that will maximize

A polutry farm owns 100 laying hens. Each week a hen can either lay 12 eggs or hatch 4 eggs, but not both. At the end of the four-week period all eggs and chicks will be sold: an egg will bring 10 cents, and a chick will bring 60 cents.

  Compute departures and latitudes and linear misclosure

Compute departures and latitudes, linear misclosure, and relative precision for a five-sided, closed traverse. It is given that the aziumuth of AB is 74 degrees 31 minutes, 17 seconds, A = 105 degrees 13 minutes 14 seconds B = 92

  How many tons of aggregate will be needed

Base course aggregate has a target dry density of 119.7 lb/cu ft in place. It will be laid down and compacted in a rectangular street repair area of 2000 ft x 48 ft x 6 in. The aggregate in the stockpile contains 3.1 percent moisture.

  Determine the shear stresses at each of the points on beam

A 6 inch X 4 inch rectangular beam is subjected to a maximum shear force of 1900 lbf. Determine the shear stresses at each of the following points on the beam cross section

  Determine the maximum concentrated load

Determine the maximum concentrated load that can be applied at the center of a 6 in. X 6 in. simply-supported plain concrete beam before it cracks in tension.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd