Determine the power required for steady speeds

Assignment Help Mechanical Engineering
Reference no: EM13708188

Extensive testing of an experimental 2820-lb automobile reveals the aerodynamic drag force FD and the total no aerodynamic rolling-resistance force FR to be as shown in the plot. Determine (a) the power required for steady speeds of 22 and 44 mi/hr on a level road, (b) the power required for a steady speed of 44 mi/hr both up and down a 5-percent incline, and (c) the steady speed at which no power is required going down the 5-percent incline.

Reference no: EM13708188

Questions Cloud

Determine the initial and final temperature of the air : A vertical piston-cylinder that initially has a volume of 0.2m^3 is filled with 0.2kg of air. The piston is weighed so that the pressure on the air is always maintained @ 2 bars. Heat transfer is allowed to take place until the volume is 75% of its i..
Find the required steam and cold water flow rates : Steam at 0.2 Mpa and 300 degrees Celsius is mixed with cold water at 20 degrees celsius and 0.2 MPa to produce 20 kg/s of saturated liquid water at 0.2 MPa. Find the required steam and cold water flow rates.
Convert the composition to atomic percent : A copper and nickel alloy has the following composition: 80wt% Cu and 20wt% Ni. Convert the composition to atomic percent.
Derive the material balance equation : Derive the material balance equation for a tank with rigid and incompressible fluids for the following conditions...The tank is initially full of oil at Pi some oil is bled off to reduce the pressure to P1 the oil removed from the tank is collected a..
Determine the power required for steady speeds : Extensive testing of an experimental 2820-lb automobile reveals the aerodynamic drag force FD and the total no aerodynamic rolling-resistance force FR to be as shown in the plot. Determine (a) the power required for steady speeds of 22 and 44 mi/hr o..
Calculate the density of the air in the round section : At one section in an air distribution system, air at 14.7 psi and 100degree F has a velocity of 1200 ft/min a and the duct is 12 in x12 in square. At another section the duct is round with a diameter of 18 inches and the velocity is 900 ft/min. Calcu..
Determine the specific volume of the rock : A rock weighs 90.8 N in air and 45 N when completely submerged in water. Determine the specific volume of the rock in m3/kg
A turbine extracts energy from water flowing through : A turbine extracts energy from water flowing through a 11-cm-diameter pipe at a pressure of 700 kPa with an average velocity of 11 m/s. If the turbine is 90 percent efficient, how much energy can be produced if the water is emitted from the turbine t..
Determine the temperature of the air and the initial volume : 1750g of air performs an expansion work of 3100kJ on the surrounding as it expands isothermally to a pressure of 63000kPa ad a volume of 0.065 cubic meters. Determine the temperature of the air and the initial volume.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Propane undergoes a process from state 1 where p114 mpa

propane undergoes a process from state 1 where p11.4 mpa t160 c to state 2 where p21.0 mpa during which the change in

  Maximum energy of distortion theory of failure

A steel circular bar (\sigmayp =250 MPa) of d=60-mm diameter is acted upon by combined moments M and axial compressive loads P at its ends. Taking M=1.5KN.m, determine, based on the maximum energy of distortion theory of failure, the largest allowabl..

  Determine the temperature rise of the contents after 08 h

a motor delivers 240 w through the drive shaft to a paddle wheel that agitates liquid water in a close insulated tank

  Air is compressed in an isentropic process from an initial

air is compressed in an isentropic process from an initial pressure and temperature of p1 90 kpa and t1 22 oc to a

  Calculate the velocity v2 imparted to barge 2 just after

two barges each with a displacement mass of 550 mg are loosely moored in calm water. a stunt driver starts his 1510-kg

  Draw a schematic of the system

(a) Draw a schematic of the system and (b) determine if the inventor's claims are true.

  If m 20 kg determine the stiffness of the spring so that

the governing equation for a simple mass-spring system exemplified in class ism? kx 0if m 2.0 kg determine the

  Use eulers method to solve this equation from t 0 to 1 d

the amount of a uniformaly distributed radioactive contaminant contained in a closed reactor is measured by its

  Velocity and acceleration of the common center of mass

The ball A is moving with constant velocity of 2 m/s and hits ball B. The ball B and C are at rest and they are connected with an unreformed spring with k= 100 N/m. All three balls are identical with 200 kg mass. Assume the impact between A and B is ..

  Evaluate the maximum theoretical power

Evaluate the maximum theoretical power that can be developed by the turbine, in kW, and the corresponding exit temperature.

  Water is pumped to 25 bar and 50 degrees c state 4 in an

consider a steam power cycle in which saturated water vapor at 25 bar state 1 enters an adiabatic steam turbine. at

  What are the hoop and axial stresses when the cylinder

a closed-end cylindrical pressure vessel constructed of carbon steel has a wall thickness of 2 mm a diameter of 150 mm

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd