Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Design a Mealy sequential circuit which investigates an input sequence X and which will produce an output of Z = 1 for any input sequence ending in 0101 provided that the sequence 110 has never occurred.
Example:
X = 0 1 0 1 0 1 1 0 1 0 1
Z = 0 0 0 1 0 1 0 0 0 0 0
Notice that the circuit does not reset to the start state when an output of Z = 1 occurs. However, your circuit should have a start state and should be provided with a method for manually resetting the flip-flops to the start state. A minimum solution requires six states. Design your circuit using NAND gates, NOR gates, and three D flip-flops. Any solution which is minimal for your state assignment and uses eight or fewer gates and inverters is acceptable. (Assign 000 to the start state.)
Test Procedure: First, check out your state table by starting in each state and making sure that the present output and next state are correct for each input. Then, starting in the proper initial state, determine the output sequence for the following
input sequences:
(1) X = 0 1 0 1 0 0 0 1 0 1 1 0
(2) X = 1 0 1 0 1 0 1 1 0 1 0 1
Assume the system shown in the Fig. is balanced, Rw = 0, Van = 208 angle 0 degree V, and positive phase sequence applies. calculate all phase and line currents, and all phase and line voltages, if Zp is equal to a) 1K ohms b) 100 + j48 ohm
Design a circuit that satisfies the equation VOUT = 5 * ( VB - VA ). Draw the circuit schematic identifying supply voltages and show your work on component selection.
As speed increases, the lower lamp, L1 lights, then L1 and L2, then, L1, L2, and L3, until all lamps light at the highest speed. Once all the lamps illuminate, no further increase in speed will have any effect on the display.
A person shuffling across a dry carpet can be approximately modeled as a charged100-pF capacitance with one end grounded. If the person touches a grounded metallic object such as a water faucet.
Within a region with volume 2.1 m^3, J=xhat*3.2*x A/m^2. What is the rate of change of total charge within the volume (in C/s)
Draw a state diagram for a synchronous sequence detector that will detect every occurence of the sequence 111001 in a serially transmitted message of any length. The sequence detector should detect overlapping sequences as well as individual occur..
Consider a linear circuit with a single voltage source Vs = 1 V and 2000 resistors. The circuit has no other sources. The current through one of the resistors in this circuit is measured to be 5 mA. If the voltage source is changed from 1 V
what is the difference between the words "rated as 3mA" , and "biased at 5mA" , when talking about a diode what is teh difference between saying " the diode is rated as a 3mA device", and " The diode is biased at a current of 0.5mA"
A turn contains three blue and seven white chips. A chip is selected at random. If the color of the chip selected is white, it is eplaced and two more white chips are added to the urn.
What should be the filter's passband cut-off frequency?(DSP Question).
Using the table, what is the byte stored at address 2F? Using the table, what is the byte stored at address 33?
A binary waveform of 53000 bits/sec is converted into an 8192 level waveform that is passed through a channel with a raised cosine-rolloff filter characteristic with r = 0.33. The channel bandwidth is what
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd