Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Determine the number of pumps needed and locations of well points. A pump test was conducted to evaluate hydrogeological information of the site, the hydraulic properties of soil and radius of influence. A fully penetrating well points with well radius of 3" was constructed and then another monitoring well was dug at a distance 50' from the center of the well. Both wells were 60' deep when both encountered tight formation of negligible permeability. Both well showed a static water-table of 10' below the surface. A well pump withdrawing 10 ft3/min resulted in drawdowns of 30' and 10' respectively at the well and monitoring location. Now you are supposed to use the above data to design a dewatering system for above the site. A building of footprint of 200'x200' to be constructed and requires 25' of depth without water to construct a basement. Assuming you have several well pumps withdrawing 10 ft3/min, Note that if you do not have symmetrical well arrangement, you need to plot contours within the building footprint show your design is acceptable for dewatering.
A 57.0 kg skier is being pulled up a 13.0° slope by a steelcable. The cable has a cross-sectional area of 7.18 10-5 m2. The cable applies a force tothe skier
An oedometer test on a clay soil gave the following results: Cc = 0.4, Ce = 0.08, OCR = 5. The thickness of the clay layer in the field is 2.6 m. The existing vertical effective stress at the mid-depth of the clay layer is 150 kPa. This vertical effe..
A 245 m ship has a displacement of 3x10^8N,and the area defined by the waterline is 3550m^2. will the ship take more or less draft when steaming from salt water to fresh water How much will it settle or rise
The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque. If the overall gear reduction ratio is 8 to 1, what is the maximum acceleration from rest (in ft/sec^2) for.
determine the deflection of a simple uniformly loaded beam by the ritz methodusing first one term then two terms adn
Roller coasters are designed so that the riders will not experience more than a certain level of g-force during the ride. (The rider would experience B g's if hte normal force were Bmg where B is a numbe
The two I-beams are welded together and are initially supported by the three cables of equal length hanging vertically from supports directly above A, B, and C. When applied with the appropriate offset
Determine the specific surfaces in m2/g units for the spheres of diameters (a) 10.0 cm, (b) 1.0 cm,(c) 0.1 cm, (d) 0.01 cm. (e) 0.001 cm and (f) 0.0001 cm. Assume the mass density of spheres as 2.5g/cc.
If the allowable stress in the cylinder is 55 MPa, what is the maximum internal diameter (nearest integer, such as 10, 11, 12, …., in units of millimetres) of the cylinder?
A group of Mr. Lugwrench engineers spent 4 years and $50,000 to develop a new pressure test system for coolant hoses with the Old Faceful Corporation. Purchasing quoted the system out, and two systems are being considered - Old Faceful and Blowi..
A tied short column of square cross-section is subjected to a factored axial load of 2500 kN and a factored bending moment of 175 kN.m. Use a 40 mm clear cover to the ties and a 20 mm maximum aggregate size.
Consider the 2 wooden beams attached in the given image. Calculate the moment around point A for ?=30. All relevant dimensions are shown.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd