Determine the normal stresses induced in portions ab and bc

Assignment Help Civil Engineering
Reference no: EM13312637

A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E=29x10^6 psi, α=6.5x10^-6) and portion BC is made of aluminum (E=6.5x10^-6 psi, α=13.3x10^-6). Knowing that the rod is initially unstressed, determine (a) the normal stresses induced in portions AB and BC by a temperature rise of 70 degrees F, (b) the corresponding deflection of point B.

Reference no: EM13312637

Questions Cloud

Developing a basic cockpit design for a new aircraft : Developing a basic cockpit design for a new aircraft
Provide a brief history of the language : Provide a brief history of the language (1-2 slides) including standards if any. What need does this language fill that others do not and discuss the language in terms of the paradigms described in Chapters 1-5 of our textbook. Provide code sample..
Calculate its approximate relative molecular mass : At an absolute pressure of 101.3 kPa and ten mperature of 20 degC the dynamic viscosity of a certain diatomic gas is 2*10^-5 Pa.sec, calculate its approximate relative molecular mass
Compute deltagrxn for the reaction : Consider the following reaction: CO(g)+2H2(g)-->CH3OH(g) Kp=2.26x10^4 Calculate deltaGrxn for the reaction at 25 C at equilibrium and when: PCh3OH = 1.1 atm, PCO = PH2 = 1.3*10^-2 atm. I got the correct original deltaG, it's -24.8 KJ
Determine the normal stresses induced in portions ab and bc : A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (E=29x10^6 psi, α=6.5x10^-6) and portion BC is made of aluminum (E=6.5x10^-6 psi, α=13.3x10^-6).
Visit the hunt library and conduct an article research : Visit the Hunt Library and conduct an article research regarding an aspect or item associated with SMS. Summarize the article, explain and correlate the relevancy of the article to the module
Define what value do you get for e using the nernst equation : What value do you get for E using the Nernst Equation? The equation is E standard = -RT/nFln[1/Cu]. The values to plug in are E = 0.340 - (8.314*298)/(2*96500)ln[1/0.10]. I calculated E = 0.31044 V. Is this correct. Any help appreciated
How many forces are acting on the block : A 2.05-kg block is on a plane at 19 degrees with respect to the horizontal. The coefficent of static friction between the block and the plan is 0.80. How many forces are acting on the block
Suppose changes in bank regulations expand the availability : Suppose changes in bank regulations expand the availability of credit cards so that people need to hold less cash.a. How does this event affect the demand for money?

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What are required amounts of components of water per sack

its desired to produce 5 cubic yards of cencrete with a ratio of 1:1.8:3.5 of cement, snd, and gravel what are the required amounts of components if 5.5 gallons of water per sack of cement is to be used

  Steps of dmaic abandoned

Assume that during the analyze stage an obvious solution is discovered. Should that solution be immediately implemented and the remaining steps of DMAIC abandoned?

  What is equivalent height of water column for pressure

Tall buildings can develop a significant difference in pressure between the inside and the outside of the building. Air lock entrances are used at the ground level so the pressure at the ground floor is not the same as atmospheric pressure.

  Qualitative or quantitative risk assessment on the project

Conduct either a qualitative or quantitative risk assessment on this project. Identify the risk factors that you consider most important for the suspension bridge construction. How would you assess the riskiness of the project? Why?

  Calculate weight of water added to reach the saturation

A soil sample with a volume of 0.5 m3, dry unit weight = 18.1 kN/m3, water content = 5%, and Specific Gravity of the soil solids = 2.68. Calculate weight of water added to reach 90% saturation (in kilograms)?

  What is the minimum chain length for the application

A motorcycle sprocket on the rear wheel has a diameter of 24 cm, and trhe driver sprocket has a diameter of 4.0 cm. The driver sprocket shaft and rear axle are 60 cm apart.

  How does the engineering classification of soils differ

How does the engineering classification of soils differ from he engineering classification of rocks

  Determine final height of the fill after compaction

A 2 m high sandy fill material was placed loosely at a relative density of 47%. Laboratory studies indicated tht the maximum and minimum void ratios of the fill material are 0.92 and 0.53, respectively.

  What do you mean by the term durability

What do you understand by the term durability? Compared to other considerations, how much importance should be given to durability in the design and construction of concrete structures?

  Find what is corresponding amplitude of the acceleration

calculate the amplitude F0 of the sinusoidal excitation force that is necessary to produce a steady-state vibration with a velocity amplitude of 10 m/s at resonance. what is the corresponding amplitude of the acceleration

  Give short explanation on principal behind how gauge works

Draw a picture of a typical strain gauge and point out the major components. Give a short explanation on the principal behind how a strain gauge works.

  Calculate the angles made by f with the postive x

a force is specified by the vector F=160i+80j-120k N.calculate the angles made by F with the postive x y and z axes.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd