Determine the normal strain in each bar

Assignment Help Civil Engineering
Reference no: EM13562652

1.The concentration of a chemical degrades in water according to first order kinetics. The degradation constant is 0.2 1/d. If the initial concentration is 100 mg/L, how many days are required for the concentration to reach 0.14 mg/L?

2.Groundwater in Taupe, Arizona, initially contains 1.8 mg/L of iron(III). What must the pH be raised to in order to precipitate 0.3 mg/L of the iron? (T=25°C)

3.The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.35 in., -0.60 in.). Assume a = 11 ft, b = 6 ft, and h = 8 ft. Determine the normal strain in each bar.

Reference no: EM13562652

Questions Cloud

Atrazine is an herbicide widely used for corn and : Atrazine is an herbicide widely used for corn and is a common groundwater pollutant in the corn-producing regions of the United States.  The log Kow for atrazine is 2.65. A typical application rate is 0.25 g/m2.
What is the vial radius of curvature : With the bubble centered, a 100-m length sight gives a reading of 1.352 m. After moving the bubble four divisions off center, the reading is 1.410 m. For 2-mm vial divisions
What is the velocity of an electron that falls through : What is the velocity of an electron that falls through a magnetic field aligned electric potential of volts across an accelertion region that is 10 k long? (neglect collisions and gravity and assume the electron has zero degree pitch-angle (i.s movin..
Determine the direction of the resultant force measured : The driver of a car traveling up a 2% grade at an initial speed of Vo applied the brakes abruptly and the vehicle slid to a complete stop at an average deceleration of 8ft/s^s. Was the pavement wet or dry?
Determine the normal strain in each bar : The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (0.35 in., -0.60 in.). Assume a = 11 ft, b = 6 ft, and h = 8 ft. Determine..
How much work must be done to move a chair : How much work must be done to move a 3.8 kg chair 6.1 m acrossthe floor at constant velocity if the coefficient of kineticfriction between the chair and the floor is 0.64
Will water bubble into the vapor phase under these : A student in the laboratory plans to exert a vacuum in the head space above a surface of water in a closed tank. She plans for the the absolute pressure in the tank to be 10,400 Pa. The temperature in the lab is 20°C. Will water bubble into the vapor..
What is the maximum amount of cargo : A small truck is to be driven down a 4% grade at 70mi/hr. The coefficient of road adhesion is 0.95, and it is known that the baking efficiency is 80% when the truck is empty and decreases by one percentage point for every 100 lb of cargo added. Ignor..
What is the maximum weight wmax of the crate that the system : Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the total equivalent future amount of the company

Vision Technologies Inc., is a small company that uses ultra-wideband technology to develop devices that can detect objects (including people) inside of buildings, behind walls, or below ground.

  Determine what would be better a truss with all 60 angles

what would be better a truss with all 60 angles or a truss with a 30 60 90 angle for a bridge design what would be the best design

  If you make decision by maximizing the expected

A manufacturing firm is considering two mutually exclusive projects. Both projects have an economic service life of one year, with no salvage value. The first cost of Project 1 is $1000 and the first cost of project 2 is $800. The Net year for each p..

  Calculate the coefficient of consolidation and compression

Briefly explain the difference between piezometer and tensiometer with respect to the working principle, special design consideration and limitation of the instrument.

  Can you conclude that the mean cost of the new method

The results, listed in dollars, were as follows: New Process 51 52 55 53 54 53 Old Process 50 54 59 56 59 58 Can you conclude that the mean cost of the new method is less than that of the old method?

  What is the over consolidation ratio of the soil

an increment of vertical stress of 150kpa compress the sample to a void ratio of1.43. what is the over consolidation ratio of the soil at the unloaded condition.

  Determine the allowable moment about the horizontal neutral

Determine the allowable moment about the horizontal neutral axis that a timber beam with nominal size 50 X 100 can resist without exceeding the allowable stress of 10 MPa. The dressed size is 38.1 X 88.9 mm, I = 0.00000223m^4, and S = 0.0000502 m^3.

  A certain pesticide is fatal to fish fingerlings at a level

a certain pesticide is fatal to fish fingerlings at a level of 0.5 parts per million in water. a leaking metal can

  Calculate the forces exerted by the water on the bend

Water flows through a horizotal 45 deg reducing bend with a 36 inch. diameter upstream and a 24 inch diameter downstream, at the rate of 20 cfs under a pressure of 15 psi at the upstream end of the bend. Neglecting head loss in the bend, calculate..

  Find compression of spring when car is momentarily bought

if the rolling resistance is 1/100 of the weight of the car, determine the compression of each spring when the car is momentarily brought to rest spring 1 500kN/m spring 2 300kN/m and distance between springs and car 30m

  Define two types of classifiers mostly used in data mining

Two types of Classifiers mostly used in Data mining. Other than Naive Bayes and decision trees, pick two other types of classifiers and discuss how they work

  Determine the young modulus of the steel alloy and the

A round steel alloy bar with a diameter of 0.75 in and a gauge length of 3.0 in was subjected to tension, with the results shown in the accompanying table. using a computer spread sheet program, plot the stress-strain relationship. from the graph, de..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd