Determine the net power delivered and the cycle efficiency

Assignment Help Civil Engineering
Reference no: EM13535624

An ideal Brayton cycle power plant operates with a regenerator of 100% effectiveness.

The air enters the compressor at 95 kPa and 290 K. At the turbine inlet, the air is at 760 kPa and 1100 K. Heat is added at a rate of 60,000 kJ/s in the combustor. Determine the net power delivered and the cycle efficiency. What is the percent increase in the efficiency compared to an otherwise identical system with no regeneration. Assume “cold air-standard cycle” for both systems above.

Reference no: EM13535624

Questions Cloud

What is the step method for drawing raft foundation : A long line of burning agricultural waste emits 0.3 g/m/s of particulate matter on a clear fall afternoon with winds blowing 3 m/s perpendicular to the line. Estimate the ground-level particulate concentration 400 m downwind from the line.
What must the hydraulic detention time be in the aeration : Although primary and secondary sedimentation is responsible for the removal of some BOD, you will design a bioreactor which removes 85% of BOD entering the plant using an activated sludge bioreactor. Use the following values: Influent (to bioreactor)..
What are alternative treatment option for the removal of edc : What are alternative treatment options for the removal of EDCs in tertiary treatment? Be sure to justify any alternative treatment method you propose.
A water pump can generate a pressure diference : A water pump can generate a pressure diference ΔP (psi) given by ΔP=145-0.1Q2, Q is the flow rate in ft3/s. It suplies a pipe of diameter 20", roughness of .5 inches and length of 2500 ft.
Determine the net power delivered and the cycle efficiency : Determine the net power delivered and the cycle efficiency. What is the percent increase in the efficiency compared to an otherwise identical system with no regeneration. Assume “cold air-standard cycle” for both systems above.
What are the heat addition rate in the combuster and the : A “Cold Air-Standard Brayton cycle” gas-turbine power plant delivers a net power output of 60 MW to an electric generator. The compressor intake temperature is 300 K and the maximum temperature in the cycle is 1200 K.
What is the diameter of the bubble before it reaches : Listed on cramster as ask. There is a car driving through water. Velocity is 12mph. Find h (max water depth) that will alow car to pass. List all assumption and calculations is the problem statement.
Calculate the minimum required cross-sectional area : The moduli of elasticity of plain concrete and steal are 25 GPa and 207GPa respectively, and the corss-sectionial area of steel is 2% of that of the reinforced concrete.
Calculate the detention time in hours horizontal velocity : Two rectangular clarifiers(sedimentation basins), each 30 ft long, 15 ft wide, and 10ft deep, settle a combinedtotal of 0.40 mgd following alum coagulation. The effluent channelshave a total weir length of 60ft in each basin

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the size of the beam with the least cross-section

A simple beam of Douglas-Fir Larch, select grade, has a span of 18 ft with two concentrated loads of 3 kips each placed at the third points of the span. Neglecting its own weight, determine the size of the beam with the least cross-section

  Determine longitudinal and hoop stresses in the copper pipe

Typical water supply at a faucet in any building is conveyed in copper pipe that is ½" in inside diameter, with a wall thickness of 0.040". If the water pressure is 50 psi and the valve is closed (meaning that water is not flowing)

  Give beam deflection solution

Beam Deflection Solution, Derive an expression for the deflection due to shear for a cantilever beam of constant rectangular cross section, under action of a point load, P at free end.

  Determine the work done in the compression process

Methane is compressed in a piston-cylinder device from initial pressure of 110 kPa and an initial temperature of 25 oC to a final pressure of 1,00 MPa. The compression process is polytropic with n = 1 .10.

  Calculate an estimate of the friction coefficient of steel

A fellow I know wanted to know the coefficient of friction between steel and commercial carpet. The value was not in the tables of any textbook he had, so he devised an experiment.

  You are part of the structural engineering design team on

you are part of the structural engineering design team on the design of a new five story office building. the

  Find ratio of he volume in colorado over that in new york

In New york you had a balloon inflated with helium (He) and you measured its temperature, which was 89.6 degree F, and its pressure, which was 100,000 N/m^2. In Colorado, however, you noticed that the temperature of the He was 69.8 degree F and th..

  How does the nature of the boundary layer affect lift

sitting on the deck one evening. watching for that pesky bunny, jon and his brother see a twig floating down from an aspen tree. (wait - os that a bunny) they wonder just what the boundary layer looks like on the twig.

  Compute the flexural strength of the load at fracture

A three-point bending test is performed on a glass specimen having a rectangular cross section of height d=5mm and width b=10mm; the distance between support points is 45mm.

  How much of a reduction in the automobile emission

How much of a reduction in the automobile emission rate would be required to achieve the maximum eight-hour average NAAQS for CO at steady state 9ppmv (10.3 mg/m3)?

  Determine what is the speed of the ballast bag when it lands

A hot air balloon starting on the ground ascends at a rate of 12 km/hr and is carried by the wind (horizontally) at a rate of 20 kn/h. When the balloon reaches a height of 50 m, a ballast bag is dropped.

  What is overall product water recovery and salt rejection

Each stage can perform 60 % water recovery (Qp/Cf) and 90% salt rejection (1-Cp/Cf) A) What is the overall product water recovery and salt rejection b)what is final product water flow rate (m^3/day) and quality in terms of TDS (mg/L).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd