Determine the moments of inertia

Assignment Help Mechanical Engineering
Reference no: EM13212197

two 20mm steel plates are welded to a rolled S section as shown. Determine the moments of inertia and the radii of gyration of the combined section with respect to the centroidal x and y axes.

Reference no: EM13212197

Questions Cloud

Explain what is the molar mass of the polymer : nonvolatitle organi polymer dissolved in 250mL of benzene has an osmotic pressure of 12.3 mmHg at 25 degree celcius. What is the molar mass of the polymer in units of g/mole?
What is the maximum possible number of station call signs : Develop the Basis Step of the algorithm to determine the number of terms of the union of n mutually intersecting sets.
Determine the velocity of the collars a and b : the motion of the slender 10kg rod AB is guided by collars of negligible mass that slide freely on the vertical and horizontal rods. knowing that the bar is released from rest when θ=30, determine the velocity of the collars A and B when θ = 60.
Explain what is the ph of the resulting solution of naoh : What is the pH of the resulting solution when 25 mL of 0.10 M NaOH is added to 25 mL of 0.25 M HNO3?
Determine the moments of inertia : two 20mm steel plates are welded to a rolled S section as shown. Determine the moments of inertia and the radii of gyration of the combined section with respect to the centroidal x and y axes.
Explain mechanism of the preparation of 2-methyl-3-hexanol : Describe the mechanism of the preparation of 2-methyl-3-hexanol by reducing an appropriate carbonyl compound.
Design a flat roof meeting certain mechanical performance : Design a flat roof meeting certain mechanical performance criteria. The basic structure of the roof is a series of rectangular-section 'joists', made from softwood, that span the space to be covered by the roof.
What is the rotating speed of the disk in rpm : A slotted disk and opto-interrupter outputs pulses at 62 HZ. The disk has only one slot cut in it. what is the rotating speed of the disk in rpm?
Determine the pressure in the evaporator : Describe IN DETAIL how you could determine the required rate of heat addition or removal.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Explain turbine of an ideal rankine cycle with reheat

Steam @ 10 MPa, 600 degrees celcius enters the first-stage turbine of an ideal Rankine cycle with reheat. The steam leaving the reheat section of the steam generator is @ 500 degrees celcius

  Calculate the thermal efficiency of this cycle

The Brayton cycle shown in figure 6.41 operates using CO2 as a working fluid with compressor and turbine isentropic efficiencies of 1.0. Calculate the thermal efficiency of this cycle when the working fluid is modeled.

  Explain aeronautical engineering module - mechanics

High school Yr 12 aeronautical Engineering Module - mechanics, PLease help- i seem to get the incorrect answer but didn't know where i have gone wrong?

  What is the rotating speed of the disk in rpm

A slotted disk and opto-interrupter outputs pulses at 62 HZ. The disk has only one slot cut in it. what is the rotating speed of the disk in rpm?

  A hydraulic cylinder is diameter

A hydraulic cylinder is 100mm diameter and is fed by a pipe 15mm in diameter. If the piston in the cylinder moves forward at a rate of 0.2ms^1

  Evaluate the exit velocity

Evaluate the valve closure to achieve a water exit velocity

  How many times more ignition energy is required

How many times more ignition energy is required to achieve ignition of a fuel-air mixture at sea level with T = 298 K than at altitude of 6000 m where pressure P = 47,166 Pa and T = 248 K?

  Applied loads and young''s modulus and poisson''s ratio

Applied Loads, Young's modulus, Poisson's ratio, The Young's modulus and the Poisson's ratio for copper are 124.8 GPa and 0.36 respectively. When a tensile load is applie to a 1.5cm diameter copper rod

  Determine the molecular weight of a poly

Determine the molecular weight of a poly(ethylene-propylene) with a degree of polymerization of 25,000 given that 20% of the mers (by number) are ethylene and 80% are propylenel.

  Calculate the heat transfer and the work done

Saturated water vapor at 200oC is isothermally condensed to a saturated liquid in a piston-cylinder device. Calculate the heat transfer and the work done during this process in kJ/kg.

  Explain a particular grade of nitinol sma is capable

A particular grade of Nitinol SMA is capable of upto 6% strain recovery and develops an internal restoration stress of upto 300 MN m-2. Estimate the amount of force and distance of travel that could be triggered by warming a rod

  Explain what is the basic design load rating

Design life is 9630 hours, rotating at 250 rpm, load of 880 lbs, what is the basic design load rating (assuming no axial loads)?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd