Determine the moment of all cable forces about point a

Assignment Help Civil Engineering
Reference no: EM13561635

Structure O A B C is built in at point O and supports forces from two cables. Cable E A D passes through a frictionless ring at point A, and cable O C G passes through a frictionless ring at point C. If the force in cable E A D is 800 lb and the force in cable O C G is 400 lb. determine the moment of all cable forces about point A

A circular disk rotates on a bearing at point A, and has a string BCD attached to it. The pulley at Cis frictionless, and the string supports a weight W = 10 lb. Determine the moment of the force in segment BC of the string about point A for any position of the disk where 0° ? ? ? 360°, and plot the moment versus ?. Neglect the size of the pulley.

Reference no: EM13561635

Questions Cloud

What is the maximum exiting velocity and what is the maximum : A fireman reduces the exit area on a nozzle so that the velocity inside the hose is quite small relative to the exiting velocity. What is the maximum exiting velocity and what is the maximum height the water can reach if the pressure inside the hose ..
Determine the moment of all cable forces about point a : Structure O A B C is built in at point O and supports forces from two cables. Cable E A D passes through a frictionless ring at point A, and cable O C G passes through a frictionless ring at point C. If the force in cable E A D is 800 lb and the forc..
Determine head loss through this pipe section : A pipe carrying oil of specific gravity (SG = 0.877) changes in size from 150 mm at section E to 450 mm at section R (E and R are arbitrary designations of the two points in the system).  Section E is 3.66 m lower than R
Take the casing wall to have an outer diameter : Batteries in a flashlight must be held in electrical contact even though the outer plastic housing expands differently than the battery and terminals. This is accomplished by having a compliant spring compressed as the cover is screwed on the flashli..
What will be the steady-state effluent concentration : A water treatment plant treats a continuous flow rate of 50,000 m^3/day and plans to build a 10,000 m^3 tank to house an additional treatment process. The reaction occurring in the tank will remove nitrate according to first order decay with a rate o..
Determine that a building solution complies with performance : In accordance with BCA, what are the assessment methods and how may they be used to determine that a building solution complies with the performance requirements?

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Calculate the pressure in point 1 and the density of fluid

A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.

  Determine the maximum and minimum dry densities

The maximum and minimum dry densities, determined by standard laboratory tests, are 1.81 and 1.54 Mg/m^3, respectively. Determine the density index of the sand.

  Determine the density of the air in a laboratory

Some experiments are being conducted in a laboratory in which theair temperature is 26o C and the atmosphericpressure is 14.6 psia. Determine the density of the air.Express your answers in slugs/ft3 andkg/m3.

  Write a loop that will estimate the value of the moody f

Use input values of epsilon (B1), pipe radius (B2), and Reynolds number (B3) to estimate "f" and place these in the same cells . Display the final answer in a message box and round to five figures. Use a short cut key of Ctrl+g

  Estimate the power in watts that can be produced

An Engineer is considering the development of a small wind turbine (D=1.25m) for home applications. The design wind speed is 15 mph at T=10C and p=0.9 bar. The efficiency of the turbine is n=20% meaning that 20% of the kinetic energy in the wind can ..

  What is the volume of the lake in cubic feet

A shallow lake can be considered a CFSTR. Nitrification, the conversion of ammonia to nitrate (NH3 -> NO3-) occurs in the lake according to first – order kinetics. One stream feeds the lake and one stream empties the lake with the flow rate in both b..

  What steady-state concentration of co will be observed

If a temperature inversion forms over the city at a height of 0.70 km, how long will it take the carbon monoxide concentration to reach 50 ppm if the wind velocity is zero If the wind velocity is 1 m/s,

  Why is the time value of money important

Why is the ‘time value of money' important for the evaluation of engineering projects? Provide at least one practical example to support your view (max 2 pages)

  Design and detail two span continuous welded plate girder

assume lateral support at each support and every 20 ft between supports. assume constant depth for girder. use A 572 grade 50steel. use LRFD methods. minimum web thickness is 5/16 inches.

  What is effective vertical stress 5 m below the top of sand

A river is 2 m deep. The river bed consists of a depth of sand of saturated unit weight 20 kN/m^3. What is the effective vertical stress 5 m below the top of the sand

  Elevation of the road at station

Given the following data for a vertical curve of a road; G1=-2.5%, G2=+5.5% and station of PVI=250+50.At station 252+50, the vertical curve must intersect an existing road at elevation 48.48ft. the elevation on the tangent section at station 256+5..

  What is the load of the member if reactor is 3 ft long

Astructural member in a nuclear reactor is made from a zirconiumalloy. If an axial load of 4 kip is to be supported by the member,determine its required cross-sectional area. Use a factor of safety of 3 with respect to yielding.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd