Determine the model design conditions

Assignment Help Mechanical Engineering
Reference no: EM131279798

A large, rigid, rectangular billboard is supported by an elastic column as shown in Fig. P7.65. There is concern about the deflection, , of the top of the structure during a high wind of velocity V. A wind tunnel test is to be conducted with a 1:15 scale model. Assume the pertinent column variables are its length and cross-sectional dimensions, and the modulus of elasticity of the material used for the column. The only important "wind" variables are the air density and velocity.

(a) Determine the model design conditions and the prediction equation for the deflection.

(b) If the same structural materials are used for the model and prototype, and the wind tunnel operates under standard atmospheric conditions, what is the required wind tunnel velocity to match an 80 km/hr wind?

1517_c5d2fcf9-b9c9-40d9-a9aa-9c9f8993b9e9.png

Reference no: EM131279798

Questions Cloud

How the portfolio manager use treasury bond futures contract : If the target duration for a portfolio is greater than the current portfolio duration, how can the portfolio manager use:- Treasury bond futures contracts to alter the portfolio's duration so as to bring it in line with the target duration?
How are they applied to general accounting : Can you describe GAAP guidelines? How are they applied to general accounting? Swayne, L. E., Duncan, W. J., &Ginter, P. M. (2013). Strategic management of health care organizations (7th ed.). Hoboken, NJ: Wiley.
Write a memorandum of the given case : write a memorandum outlining the issues of this case, including the crimes that the defendants (both Helen and Allen) can reasonably be charged with.
Sequential and additive composition adaptors : Explain how the sequential and additive composition adaptors differ in terms of their usage, their software integration, and their reuse.
Determine the model design conditions : If the same structural materials are used for the model and prototype, and the wind tunnel operates under standard atmospheric conditions, what is the required wind tunnel velocity to match an 80 km/hr wind?
Did you know the university of phoenix has career services : Did you know the University of Phoenix has Career Services just waiting to help you find that next job? Here is a webpage you should check out!
Calculate the process capability index for example : A metal fabricator produces connecting rods with an outer diameter that has a 1 ± 0.05 inch specification. A machine operator takes several sample measurements over time and determines the sample mean outer diameter to be 1.004 inches with a standard..
What is the role of the conversion factors : What is the role of the conversion factors? - What is the significance of the cheapest-to-deliver issue for a Treasury bond futures contract?
Explain the resulting position for the buyer and the writer : In determining the theoretical price of a Treasury bond futures contracts, explain why it is necessary to modify the standard cost of carry model.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Determine the average hydrogen concentration

Determine the average hydrogen concentration and change in refractive index after 1 h and 10 h of operation in the hydrogen environment.

  The boiling eventually exhibits behavior similar to that

water at atmospheric pressure boils on the surface of a large horizontal copper tube. the heat flux is 90 of the

  Determine a the average force at the wheels of the cab b

a trailer truck enters a 2 percent uphill grade traveling at 72 kmh and reaches a speed of 108 kmh in 300 m. the cab

  Wireless accelerometer is mounted to the underside of piston

A wireless accelerometer is mounted to the underside of a piston in an engine to measure the acceleration during operation. If the engine is operating at 7200 RPM, what should be the minimum natural frequency of the accelerometer in order for the err..

  The 4-mm-diameter cable bc is made of a steel with e 200

the 4-mm-diameter cable bc is made of a steel with e 200 gpa. knowing that the maximum stress in the cable must not

  To prevent condensation on the pipe surface it is insulated

in a processing plant cold water at 3degc is pumped through a 20 mm outside diameter galvanized steel pipe. the pipe

  An air standard otto cycle has the following cycle states

an air standard otto cycle has the following cycle states where state a is the beginning of the isentropic compression

  Plot the design graph of load versus concrete properties

Plot the design graph of load versus concrete properties and slip versus concrete properties. Please explain the results and Plot the design graph of load versus temperatures and slip versus temperatures.

  Develop a list of your personal and educational abilities

Develop a list of your personal and educational abilities that you think need to be strengthened. Write an essay that discusses how work experience could improve these skills for you.

  Determine the pressure head rise across the pump

Determine the pressure head rise across the pump if the discharge is Q = 115 L/s. The centerlines of the suction and discharge pipes are at the same elevation.

  Find the safety factor against failure

Show transcribed image text For the beam of length 30 inches shown below, if the tension in the cable is known to be 10 kip and F = 50 kip, find the safety factor against failure if the material was

  Diameter pipeline terminates in a nozzle of outlet diameter

A 0.3-m diameter pipeline terminates in a nozzle of outlet diameter = 0.15 m. When water flows through this pipe at a rate of 0.25 m3 /s, the force required to hold the pipe (N) is most nearly.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd