Determine the minimum required diameter for the machine

Assignment Help Civil Engineering
Reference no: EM13319123

A short, solid, compression member of circular cross section is to support a load of 100 kips. Determine the minimum required diameter for this machine member based on direct, compressive stress. The member is to be made of gray cast iron. Use a factor of safety of 6.0 against compression failure.

Reference no: EM13319123

Questions Cloud

Find max allowable force p for max allowable bearing : find the maximum allowable force P if the maximum allowable bearing stress on 6 pins holding 2plates together is σ all=10 MPa, and the maximum allowable shear stress is τ all =25 MPa
Who has the absolute advantage at producing cigar : What is the range of possible Relative Wage Ratio under which trade based on comparative is mutually beneficial and who has the absolute advantage at producing Cigar?
An increase in the demand for notebooks raises the quantity : An increase in the demand for notebooks raises the quantity of notebooks demanded, but not the quantity supplied.” Is this statement true or false
Build the time series for the index of openness : Build the time series for the Index of Openness (Export of Goods/GDP) using a spreadsheet and build the time series of Imports of Goods/GDP.
Determine the minimum required diameter for the machine : Determine the minimum required diameter for this machine member based on direct, compressive stress. The member is to be made of gray cast iron. Use a factor of safety of 6.0 against compression failure.
The relationship between the inflation rate and changes : Classify the following topics as relating to microeconomics or macroeconomics. a family’s decision about how much income to save. the effect of government regulations on auto emissions
Determine the liquid density in british gravitational units : It is commonly known that there are 16 ounces in 1 lb. Consider a 0.5lbf glass that weighs 1 lbf when filled with 8 ounces of liquid. Determine the liquid density in British gravitational units and in SI units.
Calculate and plot using a spreadsheet : Calculate and Plot using a spreadsheet the series for Real GDP and calculate and Plot using a spreadsheet the yearly % changes in Nominal GDP (i.e. [GDPt+1-GDPt]/GDPt)
Determine the density and pressure in cgs absolute units : A certain gas has a molecular mass of 40. It is under a pressure of 2.5atm and a temperatature of 25 Degree Celsius. Determine its density and pressure in CGS absolute units.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What is the moment at the free end of the cantilever

Consider a cantilever beam with a trapezoidal load along the length, a concentrated load at its free end, and an applied moment at the mid-span of the beam. What is the moment at the free end of the cantilever

  Determine the volumetric flow rate in each 15-cm duct

Air enters an electrical furnace at 20oC, 100 kPa, with a volumetric flow rate of 30 m3/min. The furnace delivers air at 40oC to a duct system with three branches consisting of two 15-cm-diameter ducts and a 30-cm-diameter duct.

  Determine the average velocity in the diameter pipe

If the average velocities in the 0.15 m and 0.2 m diameter pipes are 2 m/s and 3 m/s respectively, then find the average velocity in the 0.3 m diameter pipe

  Estimate settlement at t after the beginning of construction

The coefficient of consolidation of a clay for a given pressure range was obtained as 8x10^-3 mm^2/sec on the basis of one-dimensional consolidation test results. In the field, there is a 2-m thick layer of the same clay.

  Calculate temp of interface between steel and isulation

A stainless steel pipe (k= 17 W/m?C) is being used to convey heated oil. The inside surface temperature is 130?C. The pipe is 2 cm thick with an inside diameter of 8 cm. The pipe is insulated with 0.04 m thick insulation

  What are the cars velocity and acceleration vectors

The car's position is defined by the position vector, where . The image below shows the system projected onto the x-y plane. What are the car's velocity and acceleration vectors at this position

  Estimate low-dose cancer risk from occupational inhalation

the recommended threshhold limit value ( TLV-ACGIH) air concentration for occupational exposure to water-insoluble hexavalent chromium Cr (VI) is 0.01 mg/M^3. this concentration is based on an assumption that the individual is generally healthy an..

  Measure the distance pa, pb, pc

Measure the distance PA, PB, PC etc. from p to various point with chain or tape and plot them to scale along the co responding rays. Join the points a, b, c, etc. to give outline of survey.

  At what depth would the vertical effective stress in deposit

At what depth would the vertical effective stress in a deep deposit of clay be 100 kpa, if e=1.1 The ground water level is a 1 m delow ground surface and S=95% above the groundwater level. Neglect pore air pressure.

  How much horizontal distance is there from prism to point a

using a prism and prism pole in conjunction with a total station, the bottom of the prism pole is placed on point A. the distance from the bottom of the prism pole to the center of the prism (HR) is 4.97 feet.

  What percentage of removal should be expected for particles

Assume the settling tank behaves like an ideal sedimentation tank, what percentage of removal should be expected for particles with a settling velocity of 0.002 m/sec

  Find dissolved oxygen deficit just downstream from outfall

A POTW (a.k.a. waste water plant) 1.0 m^3/s of treated effluent having an ultimate BOD of 30mg/L and DO = 2 mg/L into a stream that has a flow of 8 m^3/s, a BOD = 5.0 mg/L and DO = 9 mg/L.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd