Determine the maximum strain energy acquired by the drill

Assignment Help Mechanical Engineering
Reference no: EM131146444

The ship at A has just started to drill for oil on the ocean floor at a depth of 5000 ft. The steel drill pipe has an outer diameter of 8 in. and a uniform wall thickness of 0.5 in. Knowing that the top of the drill pipe rotates through two complete revolutions before the drill bit at B starts to operate and using G = 11.2 X 106 psi, determine the maximum strain energy acquired by the drill pipe.

1851_efe4ec84-12f0-4a83-9c7a-3e4ee0315b9c.png

Reference no: EM131146444

Questions Cloud

Describe the conflict : Describe what you see as being the major contributor to the conflict. Is it misunderstanding? Is it emotion? Is it ethics? Is it power? Etc. Also describe who was most at fault.
How do we represent the link costs : We have discussed Dijkstra's algorithm in class for computing the shortest paths from any source node to all other nodes in a network. The first step is to codify the network information, i.e., how do we represent the link costs?
Companies prepare balance sheets in order : Prepare a personal balance sheet using the format you have learned for a classified balance sheet for a company. For the equity account, use M. Y. Own, Capital.
Provide a definition for each of the four categories : Provide a definition for each of the four categories and 10 essential services of public health listed on the worksheet. (The definition should be approximately three to four sentences each, written in your own words.)
Determine the maximum strain energy acquired by the drill : Knowing that the top of the drill pipe rotates through two complete revolutions before the drill bit at B starts to operate and using G = 11.2 X 106 psi, determine the maximum strain energy acquired by the drill pipe.
Prism company is a pesticide manufacturer : Prism Company is a pesticide manufacturer. Its sales declined greatly this year due to the passage of legislation outlawing the sale of several of Prism's chemical pesticides.
What is its new target variable cost per skier snowboarder : If SnowCastles can't reduce its costs, what profit will it earn? State your answer in dollars and as a percent of assets. Will investors be happy with the profit level? Show your analysis. Assume that SnowCastles has found ways to cut its fixed costs..
What is the difference between accrual basis accounting : Write a letter to your senators explaining why you think the federal government should adopt the accrual basis of accounting.
Prepare a correct income statement for the quarter ended : Explain to Lori the generally accepted accounting principles that she did not follow in preparing her income statement and their effect on her results.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Calculate the time average increase r in air resistance

If the velocity of the airplane in its horizontal flight is 1050 km/h at the end of the 9 s, calculate the timeaverage increase ?R in air resistance. The mass of the rocket fuel used is negligible compared with that of the airplane.

  So in the winter given the flow rates from part a and the

many commercial sinks and publicly-accessible showers have mixing valves underneath them which pre-mix the hot and cold

  What speed vb will cause the car to lose contact with the

a formula-1 car encounters a hump which has a circular shape with smooth transitions at either end. a what speed vb

  Air enters a control volume at a pressure

Air enters a control volume at a pressure of 19000lbf/ft^2, a velocity of 80ft/s and a temp of 440 degrees F. the area through which the air flows is .05 ft^2. The air behaves as an ideal gas. Determine the mass flow rate in lb/s.

  Determine the angular velocity of rod bd

Knowing that crank AB has a constant angular velocity of 160 rpm counterclockwise, determine the angular velocity of rod BD and the velocity of collar D when a. delta=0, b. delta = 90.

  If it has to be operated in 300degf maximum with fully

a forged 6061-t6 aluminum bar d1.5 in. with sut45000 psi will be used for one of the machine component. if it has to be

  How much ideal effort force is required to travel up ramp

If a person and a wheelchair have a mombined weight of 185 lb how much ideal effort force is required to travel up the ramp? Can you just explain to me what equation I need for this?

  What will be the reactions of the inner and outer wheels

What will be the reactions of the inner and outer wheels when travelling at a speed of 60 km h 1 around a level curve of radius 80 m.

  A fan accelerates air

A fan accelerates air (at atmospheric pressure and 300K) from a rest to 5m/s. The fan mass flow rate of air is 1.2 kg/s. What is the minimum amount of power this fan must consume to operate under these conditions?

  Calculate a linear least-squares equation for the data

Calculate a linear least-squares equation for the data.

  Define and design a hollow steel shaft to transmit

Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.

  If this is accomplised using a series of he-ne lasers with

a 2000kg ship initially at rest in an inertial system is accelerated along a straight line for 3.16e7 seconds by means

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd