Determine the maximum speed for each car

Assignment Help Civil Engineering
Reference no: EM131037321

The concept of variable banking for racetrack turns is shown in the figure. If the two radii of curvature are ρA = 300ft and ρB = 320ft for cars A and B, respectively, determine the maximum speed for each car. The coefficient of static friction is πs =0.90 for both cars.

218_cb46af3f-7cc7-4912-8b30-41ca5d23f598.png

Reference no: EM131037321

Questions Cloud

What is a commonly accepted definition of miracle : What is a commonly accepted definition of "miracle"? The philosopher David Hume is well known for his opposition to miracles. What are two or three of Hume's objections to miracles?
Derive the conditional distribution function : Derive the conditional distribution function of X given N = n and state your reasoning behind your derivation - derive the joint distribution function of X and N and state your reasoning behind your derivation.
A bipolar differential amplifier : 9.110 A bipolar differential amplifier such as that shown in Fig. 9.36(a) has I = 0.4 mA, VA =40 V, and β = 150. Find Gm, Ro, Ad , and Rid . If the bias current source is implemented with a simple npn current mirror, find REE, Acm, and CMRR.
What is morally permissible for us to believe : Explain James classification of hypotheses as alive or dead and the types of options used in deciding between alternative hypotheses. Explain why James does not believe it is rational to suspend belief about the existence of God and like religious m..
Determine the maximum speed for each car : determine the maximum speed for each car. The coefficient of static friction is πs =0.90 for both cars.
Complete the manufacturing budget : Complete the Manufacturing Budget on the Budgets tab below by using the information found in the budgeted balance sheet above. The manufacturing budget consists of three parts: the Raw Materials Budget, the Direct Labor Budget, and the Factory Ove..
History of business ethics and stakeholder theory in america : One thing nice about this course is that you will find your background reading page rather short... but there will still be a respectable amount of reading to do. The reason for this is because will be using a text book for your case assignments. ..
Repeat the design of the amplifier specified in problem : Repeat the design of the amplifier specified in Problem 9.108 utilizing a Widlar current source (Fig. 8.42) to supply the bias current. Assume that the largest resistance available is 2 kΩ.
Calculate the necessary angular velocity for the swings : Neglect the mass of the cables and treat the chair and person as one particle.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  What will be the probability that the pile can carry

Assume the capacity of a pile supporting a transmission tower is modeled with a log-normal random distribution with a mean of 250 tons and a c.o.v. of 20%.

  Find the value of the kinetic energy correction coefficient

assuming that the velocity variation within the main channel and the floodplain subsections is much smaller than the change in mean velocities between subsections, find the value of the kinetic energy correction coefficient.

  A simple curve has a central angle of 42degreess a point y

a simple curve has a central angle of 42degreess. a point y is located 24m from the vertex and has a perpendicular

  What are the coordinates of the point

An agronomist wants to measure the rainfall at the centroid of a plowed field between two roads. What are the coordinates of the point where the rain gauge should be placed?

  Determine the detention time in hours for the chemostat

Perform a material balance on substrate (S) around a chemostat (completely mixed reactor without recycle) assuming a first-order removal for a substrate with a rate constant of 0.5 hr-1.

  What is the undrained shear strength of the clat in kpa

A saturated clay deposit is vane-tested in-situ. A torque of 30Nm is required to shear the clat. The vane is 40mm wide by 100mm long.What is the undrained shear strength of the clat in kPa?

  What are the density volume-to-capacity ratio and level

A 5% upgrade on a six-lane freeway (three lanes in each direction) is 1.25 mi long. On this segment of freeway, the directional peak-hour volume is 3800 vehicles with 2% large trucks and 4% buses (no recreational vehicles), the peak-hour factor is 0...

  Show process on t-v diagram with respect to saturation line

An insulated rigid tank is initially filled with a saturated liquid-vapor mixture of water. Initially three-quarters of the mass is in the liquid phase, the mass is 10 lbm, and the pressure is 15 psia.

  Deisgn a thrust block needed to resist the force generated

Deisgn a thrust block needed to resist the force generated by a 45 degree flanged regular elbow which carries a flow of 14 cfs.  The diameter of the fitting narrows from 24 inches to 18 inches and the inlet pressure is 100 psi.

  Determine entropy change of air during compression process

Air is compressed from an initial state of 100 kpa and 170 *C to a final state of 600 kpa and 57 *c. Determine the entropy change of air during the compression process by using a) property values from the air table and b) average specific heats

  Determin the flow velocity within the tubes in feet per min

Consider a high-rate sedimentation basin with tube settlers. The basin is 120 feet long and 30 feet wide. The length of the basin covered by tube settlers is 90 feet.

  How many yards of borrow will be required to complete

An embarkment will be constructed with the soil compacted to 95 percent of the max dry density. the borrow material, is deposited at a uniform density of 75 percent of the max dry density. the roadway embankment will require 75,000 cubic yards of fil..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd