Determine the maximum shear stress in the shaft

Assignment Help Mechanical Engineering
Reference no: EM13718937

A hydrofoil boat has an AISI 1020 Hot Rolled steel propeller shaft that is 100 ft. long. It is connected to an in-line diesel engine that delivers a maximum power of 2500 hp and causes the shaft to rotate at 1700 rpm. If the outer diameter of the shaft is 8in. and the wall thickness is 3/8" determine.

a) the maximum shear stress in the shaft.

b) the angle of twist in the shaft

 

c) the design factor (factor of safety) assuming repeated torsion .Is it reasonable or not and why?

Reference no: EM13718937

Questions Cloud

Compute the modulus of elasticity for the nonporous material : The modulus of elasticity for a ceramic material having 5 vol% porosity is 296 GPa (43x10^6 psi). (a) Compute the modulus of elasticity for the nonporous material. (b) At what volume percent porosity will the modulus of elasticity be 231 GPa (33x10^6..
Determine the isentropic compressor efficiency : An air compressor operates under steady conditions. Air is compressed from an initial state of 295 K and 101 kPa to a final state of 430 K and 340 kPa. Ignore heat transfer between the compressor and surroundings and ignore kinetic energy and potenti..
Calculate the turbines isentropic efficiency : Water vapour enters an adiabatic turbine at a flow rate of 820 L/s. The turbine expands the water from 10 MPa and 600oC to 8 kPa and a quality of 0.9. Kinetic energy and potential energy effects can be ignored.
What is the rate of work if isentropic efficiency : A turbine receives 10 kg/s of steam at a state of p1 = 5 bar, t1 = 400?c and exhausts to a pressure of p2 = 1.5 bar. The ambient temperature is t0 = 300c and the ambient pressure is p0 = 1 bar. What is the rate of work if isentropic efficiency is 75%..
Determine the maximum shear stress in the shaft : A hydrofoil boat has an AISI 1020 Hot Rolled steel propeller shaft that is 100 ft. long. It is connected to an in-line diesel engine that delivers a maximum power of 2500 hp and causes the shaft to rotate at 1700 rpm. If the outer diameter of the sha..
Determine the resulting mixtures volume : 77 lbm of a gas whose density is .0007 lbm/ft^3 is mixed with 1.81 lbm of a gas whose density is .0018 lbm/ft^3 such that the pressure and temperature of the gases do not change. Determine the resulting mixtures volume (ft^3) and specific volume (ft^..
Volumetric analysis of a mixture of a mixture of gases : The volumetric analysis of a mixture of a mixture of gases is 30 percent oxygen, 40 percent nitrogen 10 percent dioxide, 20 percent methane. This mixture flows through a 1-in-diamter at 1500 psia and 70F with a velocity of 10 ft/s. Determine the volu..
Determine the pressure after the first stage compressor : A two-stage compressor is used to compress air from 100 kPa at 298 K to 900 kPa at a rate of 0.5 kg/s. After the first stage compressor, an intercooler isobaric ally cools the air to 350 K before entering the second compressor stage.
Rate of heat exchange per square meter between two surfaces : Two horizontal surfaces separated by a 125-mm layer of air have upper and lower temperature of 300k and 350k, respectively. Determine the rate of heat exchange per square meter between the two surfaces?

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Temperature sensors sensitivity

A temperature sensor's sensitivity is given as 5mv/0.1oF. The sensor can measure from -100oF (that is negative 100F) to 150oF. Find out the sensor possible output values for a measured value of 30F for the following accuracies: ±0.5% of FS error/ ±..

  What is the total heat gain or loss of the building for the

an office building is found to gain 200000 btuh of heat on a hot summer day over the period from 6 a.m. to 6 p.m. the

  A certain factory manufactures tin cansit receive an order

a certain factory manufactures tin cans.it receive an order for 10000 cylindrical tin cans of height 5 inch and

  Draw the complete mohr circle and sigma1sigma2 plot what is

a machine component is made of 2024-t4 aluminum. the external loads produce highest operating principle stresses that

  Find the free-fall velocity of an 85-in-diameter sphere

find the free-fall velocity of an 8.5-in-diameter sphere bowling ball weighing 16 lb falling through the following

  Small angular oscillations of bar about the vertical axis

A uniform bar of length l and weight w is suspended symmetrically by two strings, set up the differential equation of motion for small angular oscillations of the bar about the vertical axis, and determine its period.

  What is the probability of choosing any one random

best buy gives a choice of 3 cpu models 2 monitors 3 printers and 2 scanners. they can operate in any combination. in

  Unidirectional reinforced composites1 calculating the

unidirectional reinforced composites1. calculating the mechanical properties of unidirectionally reinforced composites

  What is the temperature cm from the base

What is the temperature 7 cm from the base if the rod is made of a) pure zinc b) lead c) pure gold. Which will be the hottest at this point?

  Determine the mass flow rate of hot water withdrawn from

the hot-water needs of a household are met by a 60-l electric water heater whose heaters are rated at 1.6 kw. the

  Calculate the velocity at the exit of a diffuser when air

calculate the velocity at the exit of a diffuser when air at 100kpa and 20 degree c enters it with a velocity of 500ms

  It enters this nozzle at 100 psia 200of with a velocity of

air is expanded in an adiabatic nozzle by a reversible polytropic process with n 1.3. it enters this nozzle at 100

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd