Determine the maximum length of a cylindrical walnut

Assignment Help Mechanical Engineering
Reference no: EM13705982

It is known that a long log floats with its axis horizontal. A very short log, however, floats with its axis vertical. Determine the maximum length of a cylindrical walnut log 30 cm in diameter that will cause it to float with its axis vertical.

Reference no: EM13705982

Questions Cloud

Compute the flow rate if the final duct size : Hydrogen expands isentropically from 15 bar absolute and 340 k to 3 bar absolute in a steady flow process without heat transfer. 1) compute the final velocity if the initial velocity is negligible B) compute the flow rate if the final duct size is 10..
Calculate number of vacancies per cubic meter in some metal : Calculate the number of vacancies per cubic meter in some metal at 763°C. The energy for vacancy formation is 0.79 eV/atom, while the density and atomic weight for this metal are 4.77 g/cm3 and 88.45 g/mol, respectively.
Components parallel and perpendicular to the inclined plane : The following figure shows a body on 25 deg inclined plane. The weight of the body represented by the force W is 66lb. resolve this force at point O into components parallel and perpendicular to the inclined plane.
Perfect gas undergoes a reversible polytropic process : A perfect gas (methane) undergoes a reversible polytropic process in which the polytrotic exponent is 1.4. 1) Using the first law, arrive at an expression for heat transfer per unit mass solely as a function of the temperature difference (change in T..
Determine the maximum length of a cylindrical walnut : It is known that a long log floats with its axis horizontal. A very short log, however, floats with its axis vertical. Determine the maximum length of a cylindrical walnut log 30 cm in diameter that will cause it to float with its axis vertical.
What would eb the corresponding magnitude of the force : The board is used to hold the end of a four-way lug wrench in position. A torque of 40 N.m about the x-axis is required to tighten the nut. You decided to step at the end of the wrench in order to turn it. Assume that the force provided by your foot ..
Specimen of aluminium having a rectangular cross section : A specimen of aluminium having a rectangular cross section 9.9 mm × 13.0 mm (0.3898 in. × 0.5118 in.) is pulled in tension with 35300 N (7936 lbf) force, producing only elastic deformation. The elastic modulus for aluminium is 69 GPa (or 10 × 10    6..
Weights that will double the pressure of gas inside cylinder : A vertical piston-cylinder device contains a gas at a pressure of 100kPa. The piston has a mass of 5 kg and a diameter of 12 cm. Pressure of the gas is to be increased by placing some weights on the piston. Determine the local atmospheric pressure an..
Constant pressure until piston regains its original position : A cylinder contains 1 kg of a certain fluid at an initial pressure of 20 bar. The fluid is allowed to expand reversibly behind a piston according to a law PV^2=constant until the volume is doubled. The fluid is then cooled reversibly at constant pres..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  The water in the pool is 25 feet deep and the rim of the

a garden hose is open at one end and capped closed at the other. a swimmer in an above-ground pool fills the hose

  A container has a circular hole d5cm on the bottom and is

a container has a circular hole d5cm on the bottom and is sealed by a metal ball weighs w2.452 with radius 4cm. water

  Determine the motor torque in foot-pounds required to

a servomotor is connected to a forearm axis drive shaft without any reduction drive components. the maximum weight of

  Determine the radius r of an impurity atom that will fit

determine the radius r of an impurity atom that will fit into a tetrahedral site of bcc ironr1.241 angstroms crystal

  Estimate the amount of torque needed to actuate the knee

estimate the amount of torque needed to actuate the knee near 0 deg flexion standing position based on the friction in

  The tunnel is located in boulder colorado altitude 1650 m

an intermittent wind tunnel is designed for a mach number of 4 at the test section. the tunnel operated by sucking air

  Describe the main kinds of social mechanisms

Describe the main kinds of social mechanisms that are used by people to communicate and collaborate.

  A 5 cm layer of insulation with thermal conductivity of

a 5 cm layer of insulation with thermal conductivity of 0.06 wm.c is placed between two plates of 100 and 200 degrees

  The department of energy projects that between the yeras

the department of energy projects that between the yeras 1995 and 2010 the united states will need to build new power

  Water is flowing through a 23 cm diameter pipe with a

water is flowing through a 23 cm diameter pipe with a velocity of 11 ms. the viscosity of water is 8 x 10-3 nmiddotsm2.

  The sun warms the can and contents to a final tmperature of

a can of juice consists of .06 kg of aluminum and .355 liters of liquid. consider the contents to be saturated liquid

  What are the conditions for valid object representation in

do you think the objects created in the following representation schema are always valid? justify your answers with

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd