Determine the maximum axial compressive force that can be

Assignment Help Civil Engineering
Reference no: EM13559257

1.A 440 -V shunt motor has armature resistance of 0.8 ohm and field resistance of 200 ohm . determine the back emf when giving an output of 7.64 KW at 85% efficiency ?

2.A short 60mm diameter circle bar is made of material for which the maximum safe compressive strees is 80 MPa and the maximum safe shearing strees is 30 MPa. determine the maximum axial compressive force that can be safely applied to the bar ?

Reference no: EM13559257

Questions Cloud

Calculate the number of theoretical stages required : It is proposed to reduce the concentration acetaldehyde in aqueous solution from 55% to 5% by mass, by extraction with solvent S at 293K. If a counter current multiple contactor process is adopted and 0.025 kg/s of solution are treated with an equal ..
How many tubes will the calandria require to concentrate : The specific heat of the solution can be assumed to be constant at 4.18 kJ kg-1 K. The latent heat of evaporation is 2270 kJ kg-1 for the feed and steam, the boiling point rise is 15 K. The feed temperature is 303 K.
Calculate the number of gas transfer units : Air enters a packed column containing 0.015 mol fraction of soluble component A. This is to be reduced to 1% of this value by contacting it with water which is free of A. The gas flow rate is 1 kg m-2 s-1 of and the water entering is 1.6 kg m-2 s-1. ..
What is the volume and density of the object : An object has an actual mass of 2kg and an apparent mass of 1.5kgwhen under water, what is the volume and density of the object
Determine the maximum axial compressive force that can be : A short 60mm diameter circle bar is made of material for which the maximum safe compressive strees is 80 MPa and the maximum safe shearing strees is 30 MPa. determine the maximum axial compressive force that can be safely applied to the bar ?
What is the average power developed by this engine : A Carnot engine operates between the temperatures of850K and 300K. What is the average power developed by this engine
What is the maximum feed rate that can be accommodated : A feed containing 15% by weight of solids is to be concentrated to 40 % solids using a double effect backward feed evaporator. The first effect is heated by steam at 413 K.
Describe the construction operating principle and beneficial : A 40 KVA 3300/240V.50Hz .1 phase transformer has 660 turns on the primary . determine 1, the number of turns on the secondary , 2, the maximum value of flux in the core ?
Determine the minimum length of a 5/16 inch side fillet : A plate 6 inch wide and 1/2 inch thick is lapped over and welded to a gusset plate. determine the minimum length of a 5/16 inch, side fillet weld that will be necessary if the plate is subjected to an axial stress of 20 ksi

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  When does connection capacity govern the required strength

The cost of tuition at a certain public university was $120 per credit-hour 7 years ago. The cost today (exactly 7 years later) is $255. The annual rate of increase is closest to

  Determine the daily discharge of groundwater into the canal

A canal is constructed parallel to a river 600 m away both fully penetrating an unconfined aquifer of coarse sand and fine gravel as shown in the illustration below. The aquifer is subject to an average infiltration of 2.3 m/year

  The description should include a brief history

Write a brief (No more than a few paragraphs plus the equations themselves on a) description of the three-dimensional unsteady Navier-Stokes equations as applied to water. The description should include a brief history

  Determine stretch of cord when the system is in equilibrium

The two disks each have a mass of 25kg and are attached at their centers by an elastic cord that has a stiffness of k = 1.6kN/m . Determine the stretch of the cord when the system is in equilibrium

  What shear stresses exist at the bottom points

A rectangular beam of width 300 mm and depth 450 mm supports loads producing a shear force of 300 kN at a particular section. What shear stresses exist at the following points

  Determine max value of dz if the flow is to remain laminar

The slope of the hill is such that for each 1.5 km of horizontal distance, the change in elevation is dz meter. Determine the maximum value of dz if the flow is to remain laminar, with a temperature of T=20°C and pressure all along the pipe is con..

  How is raw pig iron extracted from iron oxide ores

(a) How is raw pig iron extracted from iron oxide ores (b) Write a typical chemical reaction for the reduction of iron oxide (Fe2O3) by carbon monoxide to produce iron.

  How to design codes which deal with shear friction

However, design codes which deal with shear friction design place an upper limit on the magnitude of the shear force for which the plane can be designed. Explain why this is so.

  What is the maximum external pull in each of the 4 gears

If a tractor with 23-hp, a max speed of 3.6 mph in 1st gear and an effieiciency of 92% is operated operated down a 4% slope and the rolling resistance is 80 lb/ton, what is the maximum external pull in each of the 4 gears.

  Compute the stations of the pc and pt for each curve

An 1100 ft. straight line route survey, which had PI's at3+81.27 (I = 12o30') and 5+42.30 (I = 10o56'), laterhad 600 ft radius simple curves inserted at each PI. Computethe following: a)Curve data for each curve: Da, T, L, LC, E, and MO

  Find index r and recurrence relation compute

You will be using a large crane... lets say one with a capacity of 30T. What considerations need to be made prior to picking up a 15T load with the crane? If you are familiar with the use of a crane be sure to include the discussion of the outriggers..

  Find tensile stress that will give probability of failure

The median value of the rupture strength was 300 MPa. The ceramic is to be used for components with dimensions l=50mm, b=d=5mm loaded in simple tension along their length. Calculate the tensile stress that will give a probability of failure of the..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd