Determine the mass of ice that will melt by the time

Assignment Help Civil Engineering
Reference no: EM131030598

answer the following question

During a picnic on a hot summer day, all the cold drinks disappeared quickly, and the only available drinks were those at the ambient temperature of 75°F. In an effort to cool a 12-fluid-oz drink in a can, a person grabs the can and starts shaking it in the iced water of the chest at 32°F. Using the properties of water for the drink, determine the mass of ice that will melt by the time the canned drink cools to 45°F.

Reference no: EM131030598

Questions Cloud

Discuss the advantages and disadvantages of cloud computing : To develop knowledge and understanding of cloud computing. Discuss the advantages and disadvantages of cloud computing. Identifythe key ideas from the materials.
Prepare advertisement for position that complies federal law : Prepare an advertisement for that position that complies with federal law. This advertisement must be detailed. The minimum length of your job description must be 300 words (approximately three-fourths of a page).
Determine the amount of boundary work done : A piston-cylinder device contains 3 ft3 of air at 60 psia and 150°F. Heat is transferred to the air in the amount of 40 Btu as the air expands isothermally. Determine the amount of boundary work done during this process.
What will banks balance sheet look like at end of nine month : Assume that the bank experiences a liquidity shock exactly along the lines of its assumptions and that it can take actions exactly according to its plan. What will the bank's balance sheet look like at the end of 9 months?
Determine the mass of ice that will melt by the time : Using the properties of water for the drink, determine the mass of ice that will melt by the time the canned drink cools to 45°F.
Why equity market-based measures of leverage and volatility : Provide three rationales why equity market-based measures of leverage and volatility of a financial firm help predict its distress better than measures based on book (or accounting) and regulatory values.
Determine the rate of heat transfer from the balls : If the temperature of the balls drops to 850°C prior to quenching, determine the rate of heat transfer from the balls to the air.
Discuss impact of technology innovations on personal banking : Discuss the government's response on the credit crunch in 1929 through 1933 versus 2008 through 2010. Discuss impact of technology innovations on personal banking and competition between banks.
Determine the work done and the amount of heat transfer : Determine the work done and the amount of heat transfer for this process. Also, show the process on a P-v diagram.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Diameter circular concrete pile required to take a design

Using a safety factor of 2.00 and neglecting the pile dead weight, find the length of a 1' diameter circular concrete pile required to take a design load of 50 kips in a soil composed of two layers.

  Calculate the friction head loss per meter of pipe

When fluid of specific weight 8.2 KN/m^3 flows in a 150-mm-diameter pipe, the frictional stress between the fluid and the pipe wall is 25 N/m^2. Calculate the friction head loss per meter of pipe. If the flow rate is 42 L/s, how much power is lose pe..

  Derive an expression for the mole fraction of h3po4

150,000 mol of aqueous phosphoric acid (H3PO4) solution contains 5.00% H3PO4 by moles. The solution is concentrated by adding pure H3PO4 at a rate of 20.0 L/min.

  Determine what is the minimum pipe diameter in the tube

Helium(15 degrees celsius, 1atm) will be transported in a straight horizontal copper tube over a distance of 150 m at a rate of 0.1 m^3/s. If the pressure drop in the tube should exceed 6 in h20, what is the minimum pipe diameter

  Determine what size pipe should be use from one reservoir

The level of one reservoir is 500 ft above the level of the other, and water is flowing steadily through the pipe from one reservoir to the other.

  A consolidated-drained triaxial shear test on a normally

a consolidated-drained triaxial shear test on a normally consolidated clay yielded a drained friction angle of 28

  What is the lowest maximum cycle temperature at the engine

the pressure ratio across the compressor is 9 and the maximum temperature is 827c.the turbine and comprssor processes are adiabatic with turbine efficiency of 90% and a compressor efficiency of 85%.

  Describe what reorder point should jill use and why

Cartridges cost $120 each and require 2 weeks to obtain from the vendor. Jill uses (Q,r) policy to control inventory of cartridges. You can assume that there are 50 working weeks in a year.

  Plot the shape of the water surface from the center

a whirlpool is modeled as the combination of a free and a forced vortex. the maximum velocity in the whirlpool is 10 m/s, and the radius at the juncture of the free and the forced vortex is 10m.

  Report on field trip to coreslab structures ltd

Report on Field trip to Coreslab Structures Ltd - Reinforced Concrete Beam - Design for Flexure & Shear Considerations

  How many ton of asphalt concrete will be required to overlay

How many tons of asphalt concrete will be required to overlay a 3-mile-long, 24-ft.-wide road with 2.5 in. of wearing course asphalt concrete that has a density of 146.3 pcf

  Calculate total co2 emissions from two polices from 2011

A more conservative increase from 27.5 mpg in 2011 to 35 mpg by 2020 is supported widely in Washington. California and 13 other states + the District of Columbia hope to increase that stander to 35 mpg by 2017 and 40 mpg by 2020.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd