Determine the mass flow rate of air through the compressor

Assignment Help Mechanical Engineering
Reference no: EM13708243

Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 32 °C with a low velocity and exits at 1 MPa and 367 °C with a velocity of 6 x 10^3 m/min. The compressor is cooled at a rate of 1800 kJ/min, and the power input to the compressor is 250 kW. Determine the mass flow rate of air through the compressor.

Reference no: EM13708243

Questions Cloud

Temperature measurement device is calibrated to produce : A temperature measurement device is calibrated to produce 4-20 mA for a temperature operation range of 0-100 degree C. Sketch the input-output characteristic chart of the device, assuming linear input/output relationship.
An enclosure contains an array of circuit boards : An enclosure contains an array of circuit boards, 15 cm high and 20 cm long. The clearance between the tips of the components on the PCB and the back surface of the adjacent PCB is 0.3 cm. Each circuit board contains 75 square chips on one side, each..
Determine amount of heat removed during the cooling process : A rigid container of 0.1 m3 and negligible heat capacity contains steam at 500 kPa and 400C. If the container is cooled, determine the pressure and temperature at which steam starts to condense. Determine also the amount of heat removed during the co..
Develop technical competence in problem formulation : Develop your knowledge of key principles relating to wastewater system design - Develop technical competence in problem formulation and solution in this discipline area.
Determine the mass flow rate of air through the compressor : Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 32 °C with a low velocity and exits at 1 MPa and 367 °C with a velocity of 6 x 10^3 m/min. The compressor is cooled at a rate of 1800 kJ/min, and the power input to..
Maximum inner diameter for the shaft for a yield strength : A shaft with a 2-inch outer diameter must deliver 5000 ft-lbs of torque. The shaft must be hollow and must simultaneously carry hydraulic fluid at an internal pressure of 30,000 psi. Assuming the shaft is closed-ended, and using the von Mises yield c..
Business to succeed in today''s business environment : 750 words discussion question. How important is it for sustainable business practices to take hold in order for a business to succeed in today's business environment?
An individual, owns a proprietorship called green : 1. Roger, an individual, owns a proprietorship called Green Thing. For the year 2014, Roger has the following items:-Business income-$200,000.
Determine temperature of air at the exit : At steady state, air at 200 kPa, 325 K, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross sectional areas. The inlet cross sectional area is 6 cm squared. At the duct exit, the pressure of the air is 100 kP..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Steel reinforcement rods had been pulled to a thickness

steel reinforcement rods had been pulled to a thickness below regulatory standards. what is the effect of this

  An impeller provides 20 kj of work to the air contained in

an impeller provides 20 kj of work to the air contained in a 0.15 m3 rigid volume initially at 200kpa and 10degc.

  An ideal otto cycle has a compression ratio of 81 at the

an ideal otto cycle has a compression ratio of 81. at the beginning of the compression process air is at 95 kpa and 27

  If the turbine inlet pressure in a rankine cycle is 5mpa

if the turbine inlet pressure in a rankine cycle is 5mpa and the inlet temperature is 350c determine the efficiency of

  One-fouth kg of a gas contained within a piston-cylinder

one-fouth kg of a gas contained within a piston-cylinder assembly undergoes a constant-pressure process at 5 bar

  Which is rotating about its axis cd at an angular velocity

a disk is spinning on shaft ab and rotates at an angular velocity w215 revs with respect to shaft ab. shaft ab is

  Write a program that accepts a numerical value x from 0 to

write a program that accepts a numerical value x from 0 to 100 as input and cmputes and displays the corresponding

  Refrigerant gains heat it flows through pipe and leave pipe

Refrigerant 134a enters a 28-cm diameter pipe steadily at 200 kPa and 20C with a velocity of 5 m/s. The refrigerant gains heat as it flows through the pipe and leaves the pipe at 180 kPa and 40 C.

  A particle moves along a circular path of radius 300 if

a particle moves along a circular path of radius 300 . if its angular velocity is 2t where is in seconds determine the

  Calculate the heat flux from the interior air to the wall

a wall has inner and outer surface temperatures of 16c and 6c respectively. the interior and exterior air temperatures

  What is the increase in force exerted with every 1 in

thin rubber strips are used to provide increasing resistance to orthopedic patients during large motion exercises.the

  Four weights is to pass through the center of the raft

Three children are standing on a 5×5-m raft. The weights of the children at Points A, B, and C are 375 N, 260 N, and 400 N, respectively. If a fourth child of weight 425 N climbs onto the raft, determine where she should stand if the other children r..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd