Determine the magnitude of the polarization vector in mica

Assignment Help Electrical Engineering
Reference no: EM13266486

A parallel-plate capacitor has plates of very large extent such that the electric field is perpendicular to the plates. The plates are separated by a distance of 1mm, and a voltage of 100 V is applied to them. A slab of mica ( epsilon = 5.4 ) is inserted between the plates. Determine the magnitude of the polarization vector in the mica.

Reference no: EM13266486

Questions Cloud

Compute the compression factor z for the gas : A gas at 225 K and 40 bar has a molar volume 26% larger than that calculated from the ideal gas law. (a) Calculate the compression factor Z for the gas under these conditions. (b) Which are dominating in this sample, the attractive or repulsive force..
Determine what is the required symbol rate : consider a scenario where there is a direct path from bs to ms,while other multipath components are reflected from a nearby mountain range.the distance between the bs and ms is 10km and the distance between the bs and mountain range as well as the..
Determine the induced emf in the wire loop : a magnetic field is directed at a 40 degree angle to a plane circular loop of wire with a radius of 26.8 cm draw a diagram showing the wire loop angle and magnetic field. determine the induced emf in the wire loop
Explain carbon dioxide and nitrogen monoxide : An ideal gas mixture containing 65.0 mol% carbon dioxide and 35.0 mol% nitrogen monoxide is to be prepared by allowing gaseous carbon dioxide to fill an evacuated 30.0 L cylinder to a pressure of 2.15 bar. The temperature is 415 K.
Determine the magnitude of the polarization vector in mica : A parallel-plate capacitor has plates of very large extent such that the electric field is perpendicular to the plates. The plates are separated by a distance of 1mm, and a voltage of 100 V is applied to them.
Explain the volume percentage of co2 in a mixture : The volume percentage of CO2 in a mixture of that gas with N2 was determined by bubbling the mixture at 1.00 atm and 25*C through a solution of 0.0100 M NaHCO3 and measuring the pH. If the equilibrium pH was 6.50, what is the volume percentage of ..
Determine the kinetic energy of the proton : a proton is moving in a circular path with a radius of 8.28 cm and is moving perpendicular to a magnetic field of 57.9 mT. determine the kinetic energy of the proton
Design experiment of set of experiments which can be test : Consider the hypothesis that an isolated hair cell (the sensory cell within the cochlea) can be modeled as a linear system when a pure acoustic tone is the input and the rate of neural firing is the output. Answer the following questions about the..
Explain phenolphthalein turns pink in solutions : What % of the solution/solid was transferred over to the container

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What isthe minimum sampling frequency to avoid aliasing

a.) What isthe minimum sampling frequency to avoid aliasing b.)If the sampling frequency of fs=2500 samples/sec is used how many samples must be taken to give a frequency resolution of 10Hz

  What was the height of the initial point it was released

an 8kg block is released from the rest on a frictionless incline of angle 60.if the speed of the box is 10m/s when it reaches to the ground what was the height of the initial point it was released

  What is the average total cost for the machine in the system

The failed machine will be immediately replaced with a brand new one upon the failure and the replacement time is negligible. Each machine will cost $100,000 dollars and the system is designed to run for 5 years.

  What should be the line voltage of an ac motor

An AC induction motor is rated at 900 rpm, 200V, 60HZ 3-phase. If reduce the motor speed by reducing the line frequency to 20HZ, what should be the line voltage

  Generate a clock signal with 5 khz frequency

Write an asm HCS12 program to flash LEDs on a dragon+ board three times when SW5 is pressed with a 5 kHz frequency, and 50% duty cycle clock signal. Generate a clock signal with 5 kHz frequency, and 50% duty cycle.

  Design a circuit that provides a voltage gain of 3

Design a circuit that provides a voltage gain of + 3. Draw the circuit schematic identifying supply voltages and show your work on component selection.

  Draw a suitable circuit that includes a resistor

Place the relay in the Collector circuit, the resistor in the Base circuit and the diode in parallel with the relay to provide a path for current due to energizing the relay.

  Find the equivalent e-field and the implied flux

The solar constant at Earth orbit (1 AU = 1 Astronomical Unit - Sun-Earth distance) is ~1400 Watts/m2. Assuming that this Poynting flux magnitude can be associated with a single E- and Hfield (i.e., E × H ),

  What is the value of beta after the code executes

What is the value of beta after the following code executes if the input is 5 int beta; cin >> beta; switch(beta){ case 5: beta += 5; case 1: beta++; case 5: beta += 5; break; case 4: beta += 4; }

  Estimate the electron concentration of gold

If each gold atom donates one electron to the gold matrix at room temperature, estimate the electron concentration of gold. Is gold a conductor?

  Modulating radio frequency carriers for carry digital data

Modulating Radio Frequency Carriers to Carry Digital Data, Digital radio transmission requires the use of a carrier wave which is modulated by the digital data.

  Define the reliability of a certain automatic cutoff device

The reliability of a certain automatic cutoff device is assumed 11/12. What is the reliability of a system consisting of 4 such devices so arranged

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd