Determine the location where a hydraulic jump forms in flat

Assignment Help Civil Engineering
Reference no: EM13299935

A rectangular open channel with a width of 10 ft and n = 0.013 conveys a discharge of 300 cfs. The upstream portion of the channel has a slope of 10%, which then abruptly changes to a slope of zero downstream. The depth of flow in the downstream channel is 6 ft, and flow in the steep portion of the channel can be assumed to be uniform. Determine the location where a hydraulic jump forms in the flat part of the channel.

Reference no: EM13299935

Questions Cloud

Determine the pressure required to fill the container : If intake1=0m and intake2=0.5m, find the pressure required to fill the container when h=0.75m at both point 1 and 2. Assume the air is at atmospheric pressure until the water level passes intake 2 and the air follows isothermal compression.
How to calculate the theoretical mass of solid formed : Calculate the theoretical mass of solid formed. If the reaction in question 1 has 91.2%yield, calculate the actual mass of solid formed
Role of fluoride in prevention of dental caries : What is the primary mechanism associated with the role of fluoride in prevention of dental caries?
What will be the effective mass of the boulder : A boulder has a volume of 1 m3 and a mass of 5000 kg. what will be the effective mass of the boulder
Determine the location where a hydraulic jump forms in flat : A rectangular open channel with a width of 10 ft and n = 0.013 conveys a discharge of 300 cfs. The upstream portion of the channel has a slope of 10%, which then abruptly changes to a slope of zero downstream.
What is the most reliable source of dietary fluoride : What is the most reliable source of dietary fluoride? What mineral is critical to the synthesis of thyroxine?
At what rate is thermal energy generated in the wire : A(n) 51.6 cm length of wire when used as a resistor has a resistance of 0.00668 ?. The ends of the wire are connected to form a circular loop, At what rate is thermal energy generated in the wire
State how many grams of the acid will be required to titrate : Oxalic acid dehydrate, H2C2O4. 2H2O (formula weight = 126.1 g/mol) is sometimes used to standardize NaOH solutions. How many grams of this acid will be required to titrate 45.0 mL of 0.18 M NaOH solution
Explain how the difference in piezometric pressure : A manometer is used to measure the pressure difference between points A and B in a pipe. Water flows in the pipe, and the specific gravity of the manometer fluid is 2.8. The distances and manometer deflection are indicated.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Detremine the cfat in year 0 for the challenger and defender

The defender had a first cost of $300,000, but its market value now is only $100,000. It has chargeable expenses of $120,000 per year and no expected salvage value. To simplify calculations, assume that SL depreciation was charged at $60,000 per y..

  How to design a horizontal curve for a two-lane road

design a horizontal curve for a two-lane road. The road has 12-ft. lanes. Due to expansive excavation, it is determined that a maximum of 34 ft. can be cleared from the road's centerline toward the inside lane to provide for stopping sight distanc..

  Probelm related to when object is thrown downward

An object is thrown downward from a 150-ft cliff with a velocity of 45m/hr so that it makes an angle of 60° with vertical face of the cliff.

  What would equivalent equal monthly payment be in constant

Assume that you borrow $10,000 for five years (annual payments) at a market rate of 5%. Assuming that inflation is 3.5%, what would the equivalent equal monthly payment be in constant dollars

  Describe the measurements that would have to be taken

describe the measurements that would have to be taken and the equations that would have to be used to determine G23, V32, and E2 for a specially orthotropic transversely isotropic material from a single tensile test.

  Find allowable load p that can be supported by connection

A steel bar is attached to a wood support beam with four 20 mm diameter lag screws. The steel bar is 75-mm-wide by 6-mm-thick. For the steel bar, the yield strength is 260 MPa and the ultimate bearing strength is 350 MPa.

  Plate with respect to the surface of the liquid will be

The plate is submerged in a liquid is a vertical position with the parallel sides horizontal and the shorter parallel side at the top and exactly in the surface of the liquid. The static moment of the plate with respect to the surface of the liqui..

  Finding the gallons of mercury

How many gallons of mercury (sg=13.54) would weight the same as 5 gallons of castor oil which has a specific weight of 56.69 pcf?

  What is the concentration of ocl-

HOCL is added to water in a tank as a disinfectant. after equilibrium is reached it is found that the pH of the water in the tank is 8.2 and the gas phase partial pressure is the head space of the tank is 0.2E-7 atm. (not: henry's law constant for..

  Calculate fraction of total atrazine that will be adsorbed

Calculate the fraction of total atrazine that will be adsorbed to the soil given that the soil has an organic carbon content of 2.5%. The bulk density of the soil is 1.25 g/cm3; this means that each cubic centimeter of soil (soil plus water) conta..

  What torque is required to rotate the inner cylinder

Crude oil at 20 degrees C fills the space between 2 concentric cylinders 250mm high with diameter of 150 and 156mm. What torque is required to rotate the inner cylinder at 12 rev/min

  Define concept of cstr

Concept of CSTR, A lagoon is to be designed to accommodate an input flow of 0.10 m^3/s of nonconservative pollutant with concentration 30.0mg/L and reaction rate 0.20/day

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd