Determine the initial weight and final density of the water

Assignment Help Civil Engineering
Reference no: EM13303373

A steel tank hold 120 ft^3 of water at atmospheric pressure(14.7psi and 68.4 degrees f). the water is subjected to a 100 fold increase in pressure. determine the initial weight and final density of the water if the volume decreases by .545 ft ^3.

Reference no: EM13303373

Questions Cloud

Which is the best alternative : A city has two alternatives for improving its sewage system. Use a 4% cost of money, which is conservative for a municipality.
Determine the distances the spacecraft must be from earth : consider a spacecraft that is positioned directly between the earth and moon.the mass of the moon's is approximately 7.35 X10^22 kg, and at the instant under consideration, the moon is 3.8 X 10^8 km from earth.
How much money will he have saved at the end of year 3 : Tom is planning to invest the following amount at 4percent interest. how much money will he have saved at the end of year 3?
After how many minutes does the ice start to melt : An open container holds 0.550 kg of ice at - 15.0 degree celsius. The mass of the container can be ignored. After how many minutes does the ice start to melt
Determine the initial weight and final density of the water : A steel tank hold 120 ft^3 of water at atmospheric pressure(14.7psi and 68.4 degrees f). the water is subjected to a 100 fold increase in pressure. determine the initial weight and final density of the water if the volume decreases by .545 ft ^3.
What are the characteristics of a monopolistically competiti : Using the criteria of efficiency, define the ways a market may fail and explain how government regulation can offset the problems caused by market failure.
Calculate the average power carried by the wave : A piano wire with mass 2.90g and length 82.0cm is stretched with a tension of 35.0N. Calculate the average power carried by the wave
Compute cbr to penetrate 5 mm in calibrated rock soil : 10 kPa of pressure required to push a 3 in^2 piston 5 mm into the compacted soil. Compute the CBR (%) if the same 3 in^2 piston required 100 kPa to penetrate 5 mm in calibrated rock soil.
Explain changes needed to implement the new functionalities : Analysing and designing the changes needed to implement the new functionalities in the sample solution. Before we can start the implementation we need to analyse the project and describe the changes we will be implementing

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Determine the axial and hoop stresses at the lower end

Determine the axial and hoop stresses at the lower end of the vessel. A standpipe 12 ft in diameter and 50 ft tall is being con- structed for use as a storage tank for water with a specific weight of 62.4 lb/ft3. The wall thickness of the vessel is..

  How to calculate the ph of clean rain in the scenario

The pH of clean rain is influenced by the partial pressure of CO2 in the atmosphere. In addition, acid rain can be formed when sulfur dioxide (SO2) is discharged into the atmosphere. i) The atmospheric CO2 concentration could rise to 400 ppmv by 20..

  How to determine the npv and the profitability index

A four year financial project has net cash flows of $20,000; $25,000; $30,000; and $50,000 in the next four years. It will cost $75,000 to implement the project. If required rate of return is 20%, conduct a discounted cashflow calculation

  What proportion of the true stress is the applied stress

A 10cm long cylindrical rod of steel is elongated to become 12.1cm long by the application of a force of 10kN. 1- What is the ration of initial diameter to final diameter, assuming no net volume change

  How many gallons of water are contained in the tank

Develop a table that shows: 1) How many gallons of water are contained in the tank if the volume is measured in increments of 1 ft from the bottom to the top. 2) The mass of water at each increment, expressed in lbm.

  How to estimate the concentration of a in the reservoir

The rate constant for decay of contaminant A in the reservoir is k=1.5 (1/year). Assuming the population, discharge rate, and reservoir conditions have been stable for a long time, estimate the concentration of A in the reservoir.

  What is the moment at the free end of the cantilever

Consider a cantilever beam with a trapezoidal load along the length, a concentrated load at its free end, and an applied moment at the mid-span of the beam. What is the moment at the free end of the cantilever

  Percentage of kinetic energy

In what direction did the cue ball move after the collision? What percentage of its kinetic energy did the cue ball impart to the eight ball?

  What hydrodynamic model would you use for the system

Solar cookers can be used in less developed countries for cooking and also for thermal disinfection of water. To disinfect water, the water must be heated to about 35 Celsius for 5 hours. Of course, it takes time to raise the temperature of the wa..

  What is the finished grade elevation on the curve at station

A sag vertical curve along an existing vertical alignment begins at station 23+45 and ends at station 30+25. The initial grade coming into the curve is -2% and the grade out is +5%. What is the finished grade elevation on the curve at station

  Determine the basin dimensions

Determine the basin dimensions (width, length, depth) for a detention time of 3 hours and a length to width ratio of 4 to 1. (use English units)

  Find the steady-state concentration of pollutant in the lake

The pollutant has a reaction rate coeeficient k of 0.25/day. Assuming is pollutant is well mixed in the lake, find the steady-state concentration of pollutant in the lake.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd