Determine the initial discharge velocity from the tank

Assignment Help Civil Engineering
Reference no: EM13543442

A D0 = 10-m-diameter tank is initally filled with water 2 m above the center of a D = 10-cm-diameter valve near the bottom. The tank surface is open to the atmosphere, and the tank drains through a L = 100-m-long pipe connected to the valve. The friction factor of the pipe is given to be f = 0.015, and the discharge velocity is expressed as V = √(2gz/(1.5+fL/D)) where z is the water height above the center of the valve. Determine (a) the initial discharge velocity from the tank and (b) the time required to empty the tank. The tank is considered to be empty when the water level drops to the center of the valve

Reference no: EM13543442

Questions Cloud

Determine flow rate in a series pipe system given that rough : A sample of moist soil has a volume of 40.5 cc mass weight of 59.2 gms. After drying it has a mass weight of 48.3 grams. The specific gravity of the solids are 2.68. Compute the degree of saturation, water content and void ratio.
Revolve the pavement about its inside edge : Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve?
What should be the surface area of each tank : Do the problem again but for an alum or iron floc with an overflow rate 20 m3/day.m2?
Determine the total work produced during this adiabatic : An adiabatic piston-cylinder device equipped with a spring maintains the pressure inside at at 300kPa when the volume is 0, and 3000kPa when the volume is 5 m3. The device is connected to a steam line maintained at 1500kPa and 200 C
Determine the initial discharge velocity from the tank : Where z is the water height above the center of the valve. Determine (a) the initial discharge velocity from the tank and (b) the time required to empty the tank. The tank is considered to be empty when the water level drops to the center of the valv..
Find the center of gravity of the given composite body : The tube supports the four parallel forces. Determine the magnitude of the forces and acting at C and D so that the equivalent resultant force of the four forces acts at point O.
Will such a procedure produce a greater flowrate : A 12in diameter water main in your city has become very rough due to rust and corrosion, it has been suggested that the flowrate through the this pipe can be increased by inserting a smooth plastic liner into the pipe.
How much time should each employee spend at each in order : To avoid boredom, employees are assigned all three tasks at different times during the shift. Each employee has to work at least half an hour at each station during a five hour shift. How much time should each employee spend at each in order to maxim..
Provide the velocity distribution for steady flow case : An infinite, long, solid, vertical cylinder of radius R is located in infinite mass of compressible liquid. Provide the velocity distribution for steady flow case

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Calculate the average stress in the plane of the reduced

A 1.0-in-diameter hole is drilled on the centerline of a long, flat steel bar that is 1/2" thick and 4" wide. The bar is subjected to a tensile load of 30,000 lb. Calculate the average stress in the plane of the reduced cross section and the maxium t..

  Complete cycle of the motion

Find the time for one complete cycle of this motion if the spring constant is 21 N/m. (Assume that once the pendulum ball hits the spring there is no effect due to the vertical movement of the ball.)

  Explain the purpose of the international space station

Q. Briefly explain the purpose of the International Space Station, and list the name of all space agencies involved in building and operating it. When is the assembly of the station expected to be completed? Include the name and the expected date ..

  Show by counter example that if f isnot onto then

Suppose that F1 ο G2 =F1ο G1 then F : S→ T, G1 : T → U, G2 :T →U,. Define a function F : R2 ? R2 by F(x, y) = (x +y, x - y). . Show that if F is onto, Suppose that G1ο F = G2 ο F.

  Are there any situations when parallel flow option

Are there any situations when parallel flow option may be preferred instead of a counter flow heat exchanger

  What is the area of one of these walls

A new athletics stadium with a curved concrete roof is beingdesigned. Each of the end walls is 25 metres long. Its height ymetres is given by

  Determine time average r of total aerodynamic resistance

if the velocity of the sled 10 sec from the start is 200mi\hr, determine the time average R of the total aerodynamic and mechanical resistance to motion. neglect the loss of mass due to exhausted fuel compared with the mass of the sled

  Draw the free-body diagrams for the entire assembly or

a draw the free-body diagrams for the entire assembly or structure and each of its parts. neglect friction and the

  Determine exact expression which gives isothermal work done

A substance for which k is a constant undergoes an isothermal, mechanically reversible process from initial state(P1-->V1) to (P2-->V2), where V is a molar volume. a) Starting with the definition of k, show that the path of the process is described

  Maximum deflection of the beam

Determine the deflection of the right end of the pointer and the maximum deflection of the beam.

  Plot the magnitude of the force exerted on the gate

Plot the magnitude of the force exerted on the gate by the brace as a function of the angle of the gate, , for . Assume the weight of the gate is negligible.

  Compute and plot the water surface profile upstream of lake

A rectangular channel leading from an upstream lake has a bottom width of 20 ft, bottom slope of 0.0002, a Manning roughness factor of 0.016, a discharge of 403 cfs, and normal depth of 6.24 ft.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd