Determine the hydraulic conductivity of the sand

Assignment Help Civil Engineering
Reference no: EM13561627

The maximum dry density determined in the laboratory for a quartz sand is 1800 kg/m^3. In the field, if the relative compaction is 90%, determine the hydraulic conductivity of the sand in the field compaction condition (given that k for the sand at the maximum dry density condition is .040 cm/sec and Gs = 2.65).

Reference no: EM13561627

Questions Cloud

Determine that a building solution complies with performance : In accordance with BCA, what are the assessment methods and how may they be used to determine that a building solution complies with the performance requirements?
How many square feet of compacted cy are placed per hour : Earth whose in situ weight is 110 lb per cf and compacted weight is 124 lb per cf is placed ina a fill at rate of 280 cy per hr, measured as compacted earth. The thickness of the compacted layers is 8 in
Compute the coefficient of permeability of the soil in : Standard air is drawn from the atmosphere into a 1.25 m diameter cylindrical duct by a fan mounted inside the duct. This air is discharged down stream from the fan through a 0.6 m diameter duct at a velocity of 25 m/s and atmosphere pressure.
What is the force if the fire fighter is running towards : The water exiting a 2.5 cm diameter nozzle which is atrtached to a 7.6 cm diameter fire hose is discharged at a velocity of 25 m/s. the pressure in the hose is 380 kpa. what is the magnitude and direction of the force of the water n the nozzle, if th..
Determine the hydraulic conductivity of the sand : The maximum dry density determined in the laboratory for a quartz sand is 1800 kg/m^3. In the field, if the relative compaction is 90%, determine the hydraulic conductivity of the sand in the field compaction condition
What horsepower must be delivered to the wheels : An automobile has been designed to maintain a constant speed of 55 mph on a +5% grade. The weight of the vehicle when fully loaded is 6000 lbs. What is the total resistance in still air of this vehicle? What would be the resistance on a level road? W..
Determine whether the resultant force acts within the kern : A 5 ft square, 2 ft. deep spread footing is subjected to a concentric vertical load of 60 k and an overturning moment of 30 ft-k. that acts at a 45 degree angle from the side of the footing
Determine the amount of steam added to the air : Air at 14.7 psia, 55*F, 60 percent relative humidity is first heated to 72*F in a heating section and then humidified by introducing water vapor. The air leaves the humidifying section at 75*F and 65 percent relative humidity.
Determine the power input into the heat pump : A heat pump that operates on the ideal vapor compression cycle with refrigerant 134a is used to heat water from 16 to 56 degrees Celsius at a rate of 0.20kg/s. The condensor and evaporator pressures are 1.5 and 0.35 Mpa, respectively. Determine the p..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the maximum force

two links AB and DE are connected by a bell crank as shown. Determine the maximum force that can be safely exerted by link AB on the bell crank if the maximum allowable value for the reaction at C is 1600N.

  Determine the pressure (psi) at the bottom of the well pipe

Pressure Variation in a Fluid at Rest 1. In April 2010, the Deepwater Horizon drilling rig experienced a severe explosion and fire and sank off the coast of Louisiana. Eleven persons died, and 17 others were injured. The resulting uncontrolled oil re..

  Calculate the time needed for the particles to set

For a temperature of 10 degree C, calculate the time needed for the following particles to settle 0.3m: a) a 20um mineral particle with a specific gravity of 2.1, and b) a 2 um organic particle with a specific gravity of 1.2

  How much will it cost the state to fund the project

Northern Tundra Telephone (NIT) has received a contract to install emergency phones along a new 100-mile section of the Snow-Moose Turnpike. Fifty emergency phone systems will be installed about 2 miles apart

  Determine what would be maximum load that covers right range

The testing machin that covers the right range of load is to be chosen. it is expected to load the material up to a strains of 3%. if th material must remain elastic over that range, what would be the maximum load

  Determine the rotation of the gear at e of a-36 steel

The two shafts are made of A-36 steel. Each has a diameter of 25 mm and they are connected using the gears fixed to their ends. Their other ends are attached to fixed supports at A and B.

  Determine what is the decrease in diameter d

A bar of monel metal (length L=9 in., diameter d=0.225 in.) is loaded axially by a tensile force P. If the bar elongates by 0.0195 in., what is the decrease in diameter d What is the magnitude of the load P

  Determine the required spacing of shear reinforcement over

Determine the required spacing of shear reinforcement over the span of a 28-in-wide and 18-in-deep beam with a clear span equal to 30 ft. 2 in. the beam suports a total factored uniformly distributed load of 5.0 kips/ft.  Assume no. 4 U-stirrups wth ..

  Coefficient of curvature for each soil

Determine the effective size as well as the uniformity coefficient and coefficient of curvature for each soil. Determine also the percentages of gravel, sand, silt, and clay according to (a) ASTM, (b) AASHTO, (c)USCS, and (d) the British Standard.

  Determine what is todays price for one share of the stock

A corporation issues a new 10 year bond that has a coupon rate of 4.65% with quarterly dividend payments. Alex purchases 200 of these bonds at a price of $98.75, for a total investment of $19,750. Assuming he holds them to maturity, what will be h..

  Define the electric motor as the system and calculate rate

The electrical power supplied to the motor is 90 kW. The motor in turn delivers 100 hp at a speed of 1000 rpm to a hoist arrangement for an elevator. Define the electric motor as the system and calculate the rate of work for the system.

  Determine correct horizontal distance considering a slope

A civil engineer used a 30-m tape in measuring an inclined distance. The measured length on the slope was recorded to be 459.20 m long. The difference in elevation between the initial and the end point was found to be 1.25 m.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd