Determine the height from the ground and the time at which

Assignment Help Civil Engineering
Reference no: EM13533360

1.A 50 cm by 20 cm block weighing 150 N is to be moved at aconstant velocity of .8m/s on an inclined surface of 20 degreesfrom horizontal with a friction coefficient of .25.

a. Determine force F that needs to be applied in thehorizontal direction to move the block.

b. If a .3mm thick oil firm with a dynamic visocity of .015 Pas is applied between the block and inclined surface determine thehorizontal force F required to move the block

c. Determine the percent reduction in the required force whenthe oil film in b. is placed between the block and slope

2.Ball A is thrown vertically upward from the top of a30-m-high-building with initial velocity of 5m/s. At the same instant another ball B is thrown upward from the ground with aninitial velocity of 20m/s. Determine the height from the ground andthe time at which they pass.

Reference no: EM13533360

Questions Cloud

Deisgn a thrust block needed to resist the force : Deisgn a thrust block needed to resist the force generated by a 45 degree flanged regular elbow which carries a flow of 14 cfs.  The diameter of the fitting narrows from 24 inches to 18 inches and the inlet pressure is 100 psi.
The shortest distance in which the train can reach a speed : A monorail train starts from rest on a curve of radius 400 m and accelerates at the constant rate a_t. If the maximum total acceleration of the train must not exceed 1.5 m/s^2, determine
Please give the numberal value of the following strengths : We have a small wood deck, 8' by 8' This deckshould only have a max of five adults on it. Oneside of deck is attached to the wall of the house, and out fromthis wall is two post six feet from the wall.   Problem is the load bearing strength of the be..
Determine the maximum resisting moment mr that the beamcan : The maximum flexural stress on a transverse cross section of a beam2" x 4" with a rectangular cross section must not exceed 8 ksi.Determine the maximum resisting moment Mr that the beamcan support if the neutral axis is
Determine the height from the ground and the time at which : Ball A is thrown vertically upward from the top of a30-m-high-building with initial velocity of 5m/s. At the same instant another ball B is thrown upward from the ground with aninitial velocity of 20m/s. Determine the height from the ground andthe ti..
A two story school has interior columns that are spaced : A two story school has interior columns that are spaced 15 ft apartin two perpendicular directions. If the loading on the flat roof isestimated to be 20 lb/ft^2 determine the reduced live loadsupported by a typical interior column at
Determine what pressure head is needed from the pump to : A WTP Operator is trying to size a pump that takes water from a WTP holding tank and sends it to a house on a hill above the plant.  The operator's goal is to have 60 psi of water pressure entering the house.
Combined weight of the boatswain chair and the sailor is 90 : A sailor is being rescued using a boatswain's chair that issuspended from a pulley that can roll freely on the support cableACB amd is pulled at a constant speed by cablle CD
What is the maximum and mean velocity of flow : A thin film of oil (v=0.001 m^2/s) 2mmthick flows down to a surface inclined at 30 degrees to thehorizontal. What is the maximum and mean velocity of flow?

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Dimensions of symmetrical trapezoid plate

The plate is submerged in a liquid is a vertical position with the parallel sides horizontal and the shorter parallel side at the top and exactly in the surface of the liquid.

  Determine the maximum additional deformation of the spring

knowing that the velocity of the package is 2 m/s when it is 8 m from the spring and neglecting friction, determine the maximum additional deformation of the spring in bringing the package to rest

  Could effectively remove water from there cycling paradigm

Could effectively remove water from therecycling paradigm; and 4) the likely effects of global warming andcooling on these dynamics.

  Determine downstream depth into gradual contraction section

If the flowrate is Q = 25 ft^3/s and the upstream depth is 2 ft, determine the downstream depth. Sketch the specific energy diagram and indicate its important characteristics. Note that the specific discharges are different.

  Determine the minimum diameter a steel wire can have

If the elastic limit of steel is 5.0 10^8 Pa, determine the minimum diameter a steel wire can have if it is to support a 69-kg circus performer without its elastic limit being exceeded.

  Determine flow rate into or out of each reservoir in pipe

Three reservoirs are connected by three pipes with hA = 100 f t, hB = 20 f t, hC = 0 f t, L1 = 1000 f t, L2 = 500 f t, L3 = 400 f t and D1 = D2 = D3 = 1 f t. Determine flow rate into or out of each reservoir if friction in each pipe is 0.02.

  Plate with respect to the surface of the liquid will be

The plate is submerged in a liquid is a vertical position with the parallel sides horizontal and the shorter parallel side at the top and exactly in the surface of the liquid. The static moment of the plate with respect to the surface of the liqui..

  Explain why strain disappears when the load is removed

A cylindrical tank with inside diameter of 300mm and wall thickness of 5mm is subjected to an internal pressure of 2Mpa. The tensile stress in mpa in the wall of the tank is mostly near

  How does the engineering classification of soils differ

How does the engineering classification of soils differ from he engineering classification of rocks

  Determine what is the decrease in thickness of the 6-ft fill

A loose, uncompacted sand fill 6 ft in depth has a relative density of 40%. Laboratory tests indicated that the minimum void ratios of the sand are 0.46 and 0.90, respectively. The specific gravity of solids of the sand is 2.65.

  What is the length of steel tape having cross-sectional area

What is the length of a 200 ft. steel tape having a cross-sectional area of 0.004in2 and a modulus of elasticity of 30,000,000 lb/in2 that is standardized at a tension of 20 lb and a temperature of 68°F

  Determine the true horizontal legth of the distance measured

A 100-ft steel tape was used in the field to measure a distance of 247.53 ft. the following data represents the conditions in the field at the time of measurement: tempreture = 41 F, tension = 30 ib, and tape supported at ends only.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd