Determine the heat transfer rate per unit width from plate

Assignment Help Mechanical Engineering
Reference no: EM13717649

Water at 10C and a velocity of .6 m/s flows over one surface of a 1.5 m long flat plate maintained at 44C. Consider the following:

i) Determine the heat transfer rate per unit width (W/m) from plate.

ii) If a wire was placed near the leading edge of the plate to induce turbulence over its entire length, calculate the heat transfer rate per unit width (W/m) from the plate.

Reference no: EM13717649

Questions Cloud

What are some of the legal and ethical issues : What are some of the legal and ethical issues involved for a police psychologist when performing fitness-for-duty evaluations? As an administrator, what would you do to eliminate or decrease these issues?
Saturated liquid water is kept in piston-cylinder weight : Saturated liquid water is kept in a piston-cylinder-weight assembly at 100 kPa. Heat is added from a reservoir at 120 C so that saturated vapor is formed. Estimate the absolute availabilities in kJ/kg of saturated liquid and vapor.
How many liters of oxygen gas needed combustion : How many liters of oxygen gas at (7.410 x 10^2) torr and 22 c are needed for the complete combustion of (3.07 x 10^0) moles of propane, C3H8
Long cylindrical electrical heating element of diameter : A long cylindrical electrical heating element of diameter D=10mm, thermal conductivity k=240 W/mC, density =2700 kg/m^3 and specific heat c_p=900J/kgC is installed in a duct for which air flows in a cross flow over the heater at a temperature and vel..
Determine the heat transfer rate per unit width from plate : Water at 10C and a velocity of .6 m/s flows over one surface of a 1.5 m long flat plate maintained at 44C. Consider the following: Determine the heat transfer rate per unit width (W/m) from plate.
Looks like a cylinder except that the side is wavy : 24. An old urn is discovered that looks like a cylinder except that the side is wavy. The urn is 6 inches high. Scientists want to estimate the volume of the urn so they measure its circumference at intervals of 2 inches, and produce the follow..
To monitor the proportion of green m&m''s in packages of m&m : To monitor the proportion of green M&M's in packages of M&M's, a quality control manager picked at random 20 M&M packages, each with 300 M&M's in them. The manager computed the proportion of green M&M's across all these packages as 0.15. What ..
A maintenance group aims to improve the effectiveness : A maintenance group aims to improve the effectiveness of its repair work. The group therefore monitors the number of maintenance requests that require a second visit to complete the repair. On any given week the maintenance group responds to 20..
Discuss the relationship between the sum of the probabilitie : Discuss the relationship between the sum of the probabilities in a probability distribution and the total area represented by the bars in a probability histogram

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Fnd the ratio of the earths translational ke to its daily

find the ratio of the earths translational k.e to its daily rotational k.e. assume the orbit about the sun is circular

  A balloon behaves so the pressure is p c2v13 c2 100 kpam

a balloon behaves so the pressure is p c2v13 c2 100 kpam. the balloon is blown up with air from a starting volume of

  Prove using the increse in entropy principle that the

a two thermal reservoirs are placed in contact with each other. prove from the increase of entropy principle that heat

  Air conditioner maintains the temperature of a dwelling

An air conditioner maintains the temperature of a dwelling at 72 0F when it is 96 0F outside. If heat is transferred through the walls and ceiling at 35,000 BTU/hr. a) What is the minimum power required to run the air conditioner in hP and b) calcula..

  Are there any tricks that can make this easier

KVL provides us with another way of arriving at a complete set of equations. There are three distinct loops in the circuit. Are There Any Tricks That Can Make This Easier?

  Estimate the safety factor with respect to infinite fatigue

a cold-drawn steel shaft of 155 bhn is 12 in. long 1.25 in. in diameter and has a 0.25-in.-diameter transverse hole.

  Two kilograms of air within a piston-cylinder assembly

two kilograms of air within a piston-cylinder assembly executes a carnot power cycle with maximum and minimum

  What is the exit air speed

Air enters a machine at 373 C with a speed of 200 m/s and leaves it at 293 C. If the flow is adiabatic, and the work output by machine is 105 Nm /kg, what is the exit air speed? What is the exit air speed when machine is delivering no work?

  Why is it easier to exhale than to inhale in order to blow

why is it easier to exhale than to inhale in order to blow out a candle? how is it related to laminar flow or steady

  A closed system contains 2-kg of air undergoes an

a closed system contains 2-kg of air undergoes an isothermal process from 600 kpa and 200oc to 80 kpa. determine the

  Calculate theoretical head power and volumetric flow rate

You have a centrifugal pump with an inlet radius of 200mm, an inlet blade width of 60mm, and inlet blade angle of 50 degrees. The outlet radius is 600mm, outlet blade width is 40mm and the outlet blade angle is 70 degrees. The pump handles water and ..

  Compare advantages and disadvantages of joining method

Describe the methods used. Show a simple schematics sketch of the joining method and briefly describe the process. Compare the advantages and disadvantages of each joining method.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd