Determine the heat transfer and work transfer

Assignment Help Mechanical Engineering
Reference no: EM13710392

Ten pounds-mass of R-22 is at an initial volume of 4.059 ft3 and pressure of 200 psia. It is compressed isobaric ally until its volume is two-thirds of its initial volume. The piston is then held in place as the refrigerant cools until its temperature is 70 F. Determine the heat transfer [Btu] and work transfer [Btu] for the two-step process. Also show the process on P-v state diagram.

Reference no: EM13710392

Questions Cloud

Obtain the half-range cosine series for the function : A periodic function f(t)is of period 10 defined by f(t)=N+t2, 0
Calculate the average velocity in each section : Air at 60° F and 40 psia is flowing in a 4" diameter pipe at 0.2 slugs/sec. The pipe undergoes a conversion to a 2" by 3" rectangular duct in which T = 150°F and P = 7 psia. Calculate the average velocity in each section.
Calculate the fugacity of liquid hydrogen sulfide : Calculate the fugacity of liquid hydrogen sulfide in contact with its saturated vapor at 25.5C and 20 bar. The vapor pressure of pure water at 310.6 K is 6.455 kPa. Compute the fugacity of pure liquid water at 310.6 K when it is under a pressure of 1..
Liquid-vapor water mixture in a rigid tank : ½ kg of a liquid-vapor water mixture in a rigid tank initially at 2 bar is heated by 120V heater for 5 minutes until it becomes a saturated vapor at 4 bar. Changes in kinetic and potential energies can be ignored.
Determine the heat transfer and work transfer : Ten pounds-mass of R-22 is at an initial volume of 4.059 ft3 and pressure of 200 psia. It is compressed isobaric ally until its volume is two-thirds of its initial volume. The piston is then held in place as the refrigerant cools until its temperatur..
Property for given state and show on stated state diagram : Determine the property for the given state and show on stated state diagram:
Head space under slight vacuum-piped to natural gas boiler : 100 kmol/h of biogas (75 mol% CH4 and 25 mol% CO2) is produced in a digester and is drawn off from the headspace under a slight vacuum and piped to a natural gas burning boiler. A slight leak develops in the pipe allowing air (79 mol% N2 and 21 mol% ..
Boundary conditions for both the pipe and the insulation : Write the appropriate form of the heat equation along with reasonable boundary conditions for both the pipe and the insulation.
Determine net work output and thermal efficiency : A Rankine cycle with reheat operates between 20 kpa & 12.5 Mpa with a reheat occurring at 1.2Mpa. Steam enters both the high and low pressure turbine at 500 C, and the enthalpy of steam at the exit of high and low pressure turbines are 3050 and 2600 ..

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Size a suitable orifice plate to meter steady flow of water

Size a suitable orifice plate to meter the steady flow of water at 20 °C through 138 cm diameter pipe if the nominal flow rate expected is 200 kg/s and the pressure drop must not exceed 15 cm mercury.

  If ice is to be produced at a rate of 3500kghour what is

to make ice at 1 atm 101.3kpa water at 25 degrees c is cooled to 0 degrees c and then frozen to ice 0 degrees c by

  Determine the maximum in-plane shear strain and the maximum

a closed cylindrical storage tank contains gas under pressure p and has an inner diameter of 24 in. and a wall

  If viscous affects are negligible determine the diameter dz

water flows upward through a variable area pipe with a constant flowrate q dz is the diameter of the variable area pipe

  Get rid of the brackets as much as possible

Simplify the following terms and get rid of the brackets as much as possible. All matrices in the equations below are square 3x3 matrices, [alpha] is a scalar, and Q is an orthogonal matrix.

  An aluminum pan whose thermal conductivity is 237 has a

an aluminum pan whose thermal conductivity is 237 has a flat bottom whose diameter is 20 cm and thickness 0.4 cm. heat

  Determine the mass moment of inertia

A flywheel can be considered as being composed of a thin disc and a rim. The rim weighs 322 lb and has diameters of 24 in. and 30 in. The disc weighs 64.4 lb. Determine the mass moment of inertia about the centroidal axis about which the flywheel ..

  Determine the input power in watts

A motor has a disk mounted on its shaft. The disk has a diameter of 1 foot and weighs 60 pounds. Starting from rest, the motor rotates at 350 rpm after 5 seconds. If the motor has a 92% efficiency, determine the input power in watts.

  Determine the total electrical work the heat pump can

a carnot heat pump is to be used for heating house in winter. the house temperature is set at 25oc. one day the outdoor

  Give examples from your own experience of situations where

question 1 give examples from your own experience of situations where friction is a desirable and b

  If wood beams are available with cross secstions having h2b

a timber beam is to be selected to sustain a maximum transverse shear of vmax 50 kn without exceeding an allowable

  Consider a 770-kg man standing on a spring scale in an

consider a 77.0-kg man standing on a spring scale in an elevator. starting from rest the elevator ascends attaining its

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd