Determine the heat fluxes through the walls-roof and door

Assignment Help Mechanical Engineering
Reference no: EM13714061

The concrete walls and roof of a garage are 15-cm thick. The inside dimensions of the garage are 8-m long, 6-m wide, and 2.5-m high. The door is made of 12-mm thick hardwood and is 6-m wide and 2.5-m high. The garage is modeled in the figure below. On a cold day, the garage is electrically heated. The inside and outside surface temperatures are 5oC and -10oC, respectively. Determine the heat fluxes through the walls, roof, and the door, and the total heat transfer rate through the walls, roof, and the door. K concrete = 0.663w/mk, K wood= 0.17 w/mK

Reference no: EM13714061

Questions Cloud

Consider a recalculating flow in the power cycle : Consider a recalculating flow in the power cycle shown in the figure. The fluid flowing in 100 ft of smooth pipe have an average specific weight of 50 lbf/ft3 and average dynamic viscosity of 5×10-4 lbf.s/ft2. Head loss in the nuclear reactor is 75 f..
Determine the mass flow rate of steam entering the turbine : Steam at 2000 psi and 1200 deg F enters a turbine operating at steady state. Partway through the turbine, 34% of the entering mass flow is extracted at 700 psi and 600 deg F. The rest of the steam exits the turbine as a saturated vapour at 1 psi. The..
What is the electrical power supply to the filament : The tungsten filament in a lamp has a diameter of 0.003 in and is 6-in long. When it is maintained at 2900K, what is the amount of energy emitted by the filament if the emissivity of the filament is 0.3? If the surroundings are at 20oC, what is the e..
Determine the heat flux across the steel sheet : A 10 mm thick Teflon sheet is perfectly bonded to a large 9 mm thick type 316 stainless steel sheets. The interface is at 119?C and the outer surface of the steel sheet is at 120?C. Take K Teflon = 0.25W/m.K K 316 Steel = 13.4 W/m.K In steady state, ..
Determine the heat fluxes through the walls-roof and door : The concrete walls and roof of a garage are 15-cm thick. The inside dimensions of the garage are 8-m long, 6-m wide, and 2.5-m high. The door is made of 12-mm thick hardwood and is 6-m wide and 2.5-m high. The garage is modeled in the figure below. O..
Air modeled as an ideal gas enters a combustion chamber : Air modeled as an ideal gas enters a combustion chamber at 20 lbf/in^2 and 70F through a rectangular duct, 5 ft by 4 ft. If the mass flow rate of the air is 830,000 lb/h, determine the velocity, in ft/s.
Suppose the unity feedback system : Suppose the unity feedback system of Fig. 5.60 has an open-loop plant given by G(s) = 1=s^2. Design a lead compensation D(s) = K (s + z)/(s+p) to be added in series with the plant so that the dominant poles of the closed-loop system are located at s ..
What is the linear attenuation coefficient for this material : A material is found to have a tenth-thickness of 2.3 cm for 1.25-MeV gamma rays. What is the linear attenuation coefficient for this material? What is the half-thickness? What is the mean-free-path length for 1.25 MeV photons in this material?
Two pounds of saturated water vapor : Two pounds of saturated water vapor at 400 F are condensed to saturated liquid in a piston-cylinder device. Calculate work done and heat transfer during this process, in Btu. Be sure to draw the process on a p-v diagram.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  What does the employee coaching process involve and what

what does the employee coaching process involve and what kinds of employees will benefit from the process? describe the

  What is the volume occupied by each gas at equilibrium

An insulated rigid container is separated into two parts using a partition that is free to move and the partition allows heat transfer without any energy storage by itself. Initially 2 kg of air at 5 bar and 350 K is contained on one side of the part..

  Sheet of epoxy reinforced

A sheet of epoxy reinforced with 60% unidirectional E-glass fibers, where x is the fiber direction. Strains ex= 0.0030, ey=-0.0020, and yxy = .0025 are measured. Estimate the applied stress ox, oy, txy

  Determine the stresses and strains in the bar

Also determine the axial force and deformation of the diameter due to temperature rise. Let E = 120 GPa and Co-efficient of linear thermal expansion = 0.0000168 per °C.

  Two suppliers manufacture a plastic gear used in a laser

two suppliers manufacture a plastic gear used in a laser printer. the impact strength of these gears is measured in

  A 3-phase 25 kva 208 v 60 hz alternator generator is

a 3-phase 25 kva 208 v 60 hz alternator generator is operating under balanced conditions and supplies a current of 20 a

  Refrigerant 134a enters the capillary tube of a

refrigerant 134a enters the capillary tube of a refrigerator as a saturated liquid at 0.8 mpa and is throttled to a

  Calculate the required volumetric flow rate in liters per

you are building a small hydroelectric generator for a hospital in a remote village. the hospital needs approximately

  A 3000-lb car accelerates under constant power from 60

a 3000-lb car accelerates under constant power from 60 mileh to 90 mileh on a 0.25 mile straight level test track.

  Determine the crack growth for cycle

Determine the crack growth for cycle #3 using Wheeler's retardation model (m=2)-finite width correction factor for SIF

  How to determine the cop of this system given only that the

a cycle is characterized by the following three processes process 1-2 is defined to be a constant pressure expansion.

  A machinist is making engine parts with axle diameter of 07

a machinist is making engine parts with axle diameter of 0.7 inch. a random sample of 15 parts shows mean diameter

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd