Determine the hardnesses expected at each point

Assignment Help Mechanical Engineering
Reference no: EM131274732

A 1050 steel is welded. After cooling, hardnesses in the heat-affected zone are obtained at various locations from the edge of the fusion zone. Determine the hardnesses expected at each point if a 1080 steel were welded under the same conditions. Predict the microstructure at each location in the as-welded 1080 steel.

422_d19c6c40-893b-49fe-87d2-19b8390f7ed7.png

Reference no: EM131274732

Questions Cloud

Can perform multiple functions : Use Case Diagram in Microsoft Visio® (or similar program) that shows typical scenarios of how a typical user might interact with the website. You must have at least seven different uses identified for your use case context diagram. If you have les..
What is simple network management protocol : 1. What is Simple Network Management Protocol (SNMP)? 2. Describe SNMP Basics and Operations. 3. SNMP Cryptographic Fundamentals
Provides a road map that management can implement : The outline should not be a reiteration of motivation theory, but should provide succinct points that cover the key topics of motivation and provides a road map that management can implement to improve motivation within the organization.
What is the role of retained austenite in this case : Why is it that the strength of the heat-affected zone is higher for low-carbon steels? What is the role of retained austenite, in this case?
Determine the hardnesses expected at each point : Determine the hardnesses expected at each point if a 1080 steel were welded under the same conditions. Predict the microstructure at each location in the as-welded 1080 steel.
The dangers of punishing the defendant for the damage : What could be the dangers of punishing the defendant for the damage the defendant has caused to individuals who are not in court?
Explain the major components of your culture : Explain the various symbols associated with your culture including their meanings. Describe the other cultures you are integrated with besides your own. What are the similarities and differences between these cultures with which you are connected?
The court of appeals either granted or denied the appeal : The district court dismissed the suit, and the plaintiffs appealed. Why do you believe the court of appeals either granted or denied the appeal?
Describe darwins theory of natural selection : Describe Darwin's theory of natural selection. Explain the 4 main processes of population genetics & evolution. Explain the importance of mutation in natural selection. Describe mitosis & meiosis. Which is most important in evolution?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Why are ultraviolet emitting sources avoided

Why are ultraviolet emitting sources avoided?

  Find the relative velocity of the systems

Find the relative velocity of the systems.

  Calculate the electrode potentials of the half-cells

Calculate the electrode potentials of the following half-cells.

  What is the entropy changedetermine the change in entropy

air is compressed in a standard compressor. its intital state is 100 kpa at 17 c and its final state is 600 kpa and 57

  Find the expression for the maximum response

Derive an expression for the time at which the response of a critically damped system will attain its maximum value. Also find the expression for the maximum response.

  A a temperature just above 912degc the structure is fcc a

iron undergoes a polymorphic transformation at 912degc. at a temperature just below 912degc it has a bcc structure a

  Determine the mass of lithium and the mass of iodine that

the anode and cathode reactions for a lithium-iodide battery are shown in your textbook on page 330. note that an

  Determine the maximum tensile compressive

Determine the maximum tensile, compressive, and shear stresses acting on the cross section of the tube at point A of the hitch bicycle rack shown in the figure.

  Calculate the lowest tm mode possible

If a wave at twice the lowest TE cutoff frequency propagates along the waveguide, calculate the wave impedance for the TE and TM modes and compare with the wave impedance for TEM modes.

  What controls the required number of prony series terms

How many Prony series terms should be experimentally determined before using linear viscoelasticity?

  Compute the maximum spacing allowed for no three single-loop

Clear span is 32 ft. Beam width b = 12 in., d = 22 in., f′c = 4000 psi, and fy = 60,000 psi. Determine the maximum spacing allowed for No. 3 single-loop stirrups at the critical section.

  Calculate the entrance and exit specific flow

a steady flow air compressor takes 5.00 kgmin of atmospheric air at 101.3 kpa and 20.0degc and delivers it at an exit

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd