Determine the governing load combination for both moments

Assignment Help Civil Engineering
Reference no: EM13315429

A beam that is part of a rigid frame has end moments and mid-span moments for dead, live, and earthquake loads. Determine the governing load combination for both negative and positive moments at the ends and mid-span of the beam. Earthquake load can act in either direction, generating both negative and positive moments in the beam.

End Moments (ft-kip) Mid-Span Moments (ft-kip)
Dead Load -180 +90
Live Load -150 +150
Earthquake ±80 0

Reference no: EM13315429

Questions Cloud

Determine how many moles of hclo4 are in 1 l : The density of 70.5 wt% aqueous perchloric acid is 1.67 g/mL. a. How many grams of solution are in 1.000 L b. How many grams of HClO4 are in 1.000 L c. How many moles of HClO4 are in 1.000 L
Cost benefit analysis : Australian Standard for lighting to firstly ensure compliance with the standard and compatibility with current fixtures (T8 linear fluorescent);
Find the frequency of the wave : The distance between two successive minima of a transverse wave is 2.57 m. Five crests of the wave pass a given point along the direction of travel every 12.4 s. Find the frequency of the wave
How many grams of water are in the same solution : How many grams of perchloric acid, HClO4, are contained in 37.6 g of 70.5 wt% aqueous perchloric acid. How many grams of water are in the same solution.
Determine the governing load combination for both moments : A beam that is part of a rigid frame has end moments and mid-span moments for dead, live, and earthquake loads. Determine the governing load combination for both negative and positive moments at the ends and mid-span of the beam.
Calculate the total weights and values of each subset : Use the decrease-by-one technique to generate the power set and calculate the total weights and values of each subset, then find the largest value that fits into the knapsack and output that value.
Determine what is the actual length of the line for steel : A 100ft steel tape measure correctly when supported throughout its length under a tension of 1- lb and at a temperature of 72F.It is used on the field at a tension of 18 lb and supported at the two ends only.
How many watts of power would it take to heat 1 l of water : How many watts of power would it take to heat 1 L of water(weighing 1.0 kg) by 10 degrees Celsius n 1.0 h Assume no heat losses occur, so all of the energy expneded goes into heating the water.
What distance on 5 grade should be laid out with a tape : What distance on 5% grade should be laid out with a tape that measures 30.010 m under field conditions if the horizontal distance is to be 430.00m

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  How to select and apporpriate value of gs for the soil

A strata of clean, light-colored quartz sand located below the groundwater table has a moisture content of 25.6%. The minimum and maximum void ratios of this soil are 0.380 and 1.109, respectively

  Determine the percent finer than each sieve

Determine D10, D30, and D60Effective grain size c. Cu d. Cz Sieve Number Opening (mm) Mass of soil retained (g) No. 4 4.750 28 No. 10 2.000 42 No. 20 0.850 48 No. 40 0.425 128 No. 60 0.250 221 No. 100 0.150 86 No. 200 0.075 40 Pan 24

  Design size of smoke vents in the ceiling with the objective

A storage room in an industry has a floor area of 30 m by 50 m and a height of 10 m. A garage door has a width of 3 m and a height of 3 m and the room has four windows that are 0.9 m by 0.9 m, situated at the height of 1 m from the floor.

  Determine what is the height of the column of water

If water at 70 degrees C (row=1.94 slugs/ft^3, vapor pressue= 0.363psia) is used in a simple barometer what is the height of the column of water if the atmospheric pressure is 15 psia

  Depreciation using straight line-double declining balance

Calculate the depreciation using straight-line, double-declining-balance (DBB), and MACRS (current IRS regulation) methods; and tabulate the depreciation schedule.

  Calculate the elastic recovery

A 10-mm diameter bar of 1040 carbon steel is subjected to a tensile load of 50,000 N, taking it beyond its yield point. Calculate the elastic recovery (or strain) that would occur upon removal of the tensile load.

  Determine the inlet and exit tempertures and exit quality

A steady flow of refrigerant 134a enters a throttling valve in a refrigeration unit as a satrurated liquid with a pressure of 150 psia. The refrigerant is discharged with a pressure of 40 psia.

  Determine the of silty clay porosity and bulk unit weight

a saturated silty clay encountered in a deep excavation is found to have a water content of 23.5%. determine its porosity and bulk unit weight.

  Determine the x coordinate of center of gravity of pulley

A flat-belt idler pulley is molded from polystyrene with a bronze bushing. Knowing that the densities of polystyrene and bronze are 640 kg/m3 and 9100 kg/m 3, respectively, determine the x coordinate of the center of gravity of the pulley.

  Why the prediction are less than the observed result

why the prediction are less than the observed result of connection in tension experiment?

  Determine maximum moment in the beam if spinned at both ends

If the live load on a 30 foot long beam is 1.2 kip/feet and the dead load is 0.8 kip/feet determine the maximum moment in the beam (kip-ft) if it is pinned at both ends. Assume the weight of the steel is 0.3 kip/feet.

  Determine a maximum safe speed to the nearest 5 mph

The central angle is 35 degrees, the super elevation is 0.08, and 20.6 is the cleared (for sight distance) from the inside edge of the innermost lane. Determine a maximum safe speed to the nearest 5 mph.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd