Determine the force that will produce an elastic reduction

Assignment Help Mechanical Engineering
Reference no: EM13216874

A cylindrical bar of aluminum 19 mm (0.75 in) in diameter is to be deformed elastically by application of a force along the bar axis. Using E=10 psi (Modulus of Elasticity), determine the force that will produce an elastic reduction of 1e-4 in. in the diameter.

Reference no: EM13216874

Questions Cloud

Compute the atomic packing factor : the unit cell for uranium has orthorhombic symmetry, with a, b and c lattice parameters of 0.286, 0.587 and 0.495nm, respectively. if its density, atomic weight, and atomic radius are 19.05g/cm3, 238.03g/mol and 0.1385 nm respectively, compute the..
What restriction justifies limitation on his speech : murray orr is arrested for screaming obscenties on his front lawn at 3:00 in the morning. what restriction justifies limitation on his speech?
Determine the magnitude of the boats acceleration : Starting from rest the motorboat travels around the circular path,P = 50m , at a speed v=(0.8t)m/s, where t is in seconds. Determine the magnitude of the boat's velocity when it has traveled 40m. Determine the magnitude of the boat's acceleration ..
Magnitude of the charge on the ballon : An inflated rubber ballon is rubbed with a wool cloth until an excess of a billion electrons is on the ballon. What is the magnitude of the charge on the ballon?
Determine the force that will produce an elastic reduction : A cylindrical bar of aluminum 19 mm (0.75 in) in diameter is to be deformed elastically by application of a force along the bar axis. Using E=10 psi (Modulus of Elasticity), determine the force that will produce an elastic reduction of 1e-4 in. in..
Describe how supervisor should state minimum job requirement : Explain how the supervisor might communicate to his or her department (of all male employees) when a female is about to become part of the work team.
Determine the minimum required wire diameter : a large tower is to be supported by a series of steel wires.it is estimated that the load on each wire will be 11100N. determine the minimum required wire diameter assuming a factor of safety of 2 and a yield strength of 1030MPa.
Why did the united states use atomic weapons against japan : "Why did the United States use atomic weapons against Japan? Do you believe President Truman made the right decision?
Determine the magnitude and direction of the resultant : The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension is 510 N in cable AB and 765 N in cable AC, determine the magnitude and direction of the resultant of the forces exerted at A by the two cables.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Explain how can be determined the dynamic parameters

How can be determined the dynamic parameters of a second order system, wiht an Inertia (M), a dampening coeficient ( C ) and a Stiffness constant ( K).

  Determine number of atoms contained within each of plane

Assuming that within metal crystals, the atoms can be considered as hard spheres in contact, sketch arrangement of atoms in a (100) plane, a (110) plane and a (111) plane of face-centered cubic structure. Determine the number of atoms contained wi..

  What is the total heat loss

A vertical run of copper tubing, 5 mm in diameter and 20 cm long, carries condensation vapor at 60 °C through 27°C air. What is the total heat loss?

  You are to supply a design for an engine room crane

You are to supply a design for an engine room crane which will provide maintenance support for the main engine. Your design should include the rails the crane will sit on.

  Complete the sketch of the obtuse triangle

Complete the sketch of the obtuse triangle. It must have an area of 1.75 in.2. Prove the geometry by dimensioning the sketch and showing the area calculation. Show only those dimensions needed for the area calculation. Note: each grid unit = .25 i..

  Explain what is thermal efficiency and the moisture content

Each turbine stage isentropic efficiency of 85% FWH is open T-S diagram for cycle? What is thermal efficiency and the moisture content of the steam leaving the low-pressure turbine?

  Why is it appropriate to take velocity measurements

Why is it appropriate to take velocity measurements at several diameters downstream of the fan?

  Is there a good calculation model for the material flow

Is there a good calculation model for the material flow through a combine harvester related to the harvesting speed?

  Determine isentropic efficiency of the compressor

Carbon dioxide enters an adiabatic compressor at 100kPa and 300K at a rate of 0.5kg/s and exits at 600kPa and 450K. Considering constant specific heat, determine (a) isentropic efficiency of the compressor (b) the rate of entropy change in (kW/K) ..

  Determine vertical distance between two consecutive drops

Water drips at the rate of 5 drops per second from a leaking tap. Determine the vertical distance between two consecutive drops after the lower drop has attained a velocity of 3 m/s.

  Sketch the cycle on p-v coordinates

Two kilograms of air within a piston-cylinder assembly execute a carnot power cycle with maximum and minimum temperatures of 750k and 300k, respectively.

  Calculate the friction loss in the turbine

If the efficiency of the turbine in converting the mechanical energy given up by the fluid to the turbine shaft is 89% (nt = 0.89), calculate the friction loss in the turbine in J/kg.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd