Determine the flow depth velocity and froude number after

Assignment Help Civil Engineering
Reference no: EM13549314

1.Water flowing in a wide channel of depth 35 cm undergoes hydraulic jump that resulted in energy dissipation of 72%.

Estimate (a) the downstream depth, (b) the volume flow rate per meter of width.

2.In 2006, the united states emitted 6,000 million metric tons (Mt) of CO2, 26.6 MtCH4, and 1.2 MtN2O. using 100 year global warming potentials, whats is the equivalent CO2 emission rate of the total for these three gases, in GtC-eq/yr

3.Water is being transported in a wide channel at a depth of 0.6 m and a velocity of 10 m/s undergoes a hydraulic jump. Determine the flow depth, velocity and Froude number after the jump, the head loss associated with jump, the energy dissipation ratio, and the wasted power production potential due to the hydraulic jump.

Reference no: EM13549314

Questions Cloud

Determine the relationship between the discharge and the : A fluid of density rho flows steadily downward between the two vertical, infinite, parallel plates. The flow is fully developed and laminar. Make use of the Navier Stokes equation to.
A well hit golf ball travels at a speed of 150 mph : A well hit golf ball travels at a speed of 150 mph ( 220 ft/s) as it leaves the tee. The golf ball has a diameter of 1.70 in and weighs 0.099 lb. Assuming standard atmospheric conditions (mu, u air = 3.74 * 10^-7 lb-s/ft2 and rho = 0.00238 slug/ft3) ..
A chemical engineer is considering two styles of pipes for : A chemical engineer is considering two styles of pipes for moving distillate from a refinery to the tank farm. A small pipeline will cost less to purchase (including valves and other appurtenances) but will have a high head loss and, therefore, a hig..
Consider the steady viscous flow through a small horizontal : Consider the steady viscous flow through a small horizontal tube. for this type of flow, the pressure gradient along the tube should be a function of the dynamic viscosity, the mean velocity and the diameter of the tube. use dimensional analysis to d..
Determine the flow depth velocity and froude number after : In 2006, the united states emitted 6,000 million metric tons (Mt) of CO2, 26.6 MtCH4, and 1.2 MtN2O. using 100 year global warming potentials, whats is the equivalent CO2 emission rate of the total for these three gases, in GtC-eq/yr
Calculate the maximum shear force v that : If the allowable shear stress is 100 MPa, calculate the maximum shear force V that a W460 X 60 structural steel wide flange is capable of resisting. Use the average web shear approach.
Find the conjugate depths of the jump formed in such : The discharge through a 6.0 ft wide rectangular channel is 200.0 ft^3/s. Find the conjugate depths of the jump formed in such a channel if 3.5 ft of energy head is lost through it.
What is a working excel vba function to perform : A ballon weighing 3.5 lb is 6 ft in diameter. if filled with hydrogen at 18 psia and 60 degrees F and released, at what U.S standard altitud will it be neutral?
Determine the dimensions of the best cross section if the : Water is to be transported at a rate of 60,000 gallons/min in uniform flow in an open channel whose surface are lined with clay tile. The bottom slope is 0.0014.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine length of the cable between the pulleys a and b

Cylinders C and D are attached to the end of the cable. if D has a mass of 600 kg, determine the required mass of C, the maximum sag h of the cable, and the length of the cable between the pulleys A and B.

  Explain how to calculate the mcl for the acceptable risk

the water is pumped out of the aquifer at a rate of 2000 gpd, treat it with activated carbon and then put it back into the aquifer. At the flow rate how long until al the PCE is removed, assume carbon removed 100% of the PCE

  Select a hydraulic pump size and a hydraulic cylinder size

Hydraulic cylinders with a stroke of 72 inches are available with bore sizes from 2 o 8 inches. Hydraulic piston pumps with an operating pressure range from 200 to 3000 psig are available with pumping capacities of 5, 10, and 15 gallons per minute..

  What is the carbon concentration at 4 mm below surface

A 1045 steel will be heat treated in air at 900 C. What is the carbon concentration at 0.4 mm below the surface after 6 hours

  How many kilowatt-hours of electricity would be saved

Suppose the utility encourages its customers to replace their 75-W incandescents with 18-W compact fluorescent lamps (CFL) that produce the same amount of light. Over the 10,000-hr lifetime of a single CFL,

  How siphon works and what is its drawing

Biofilter AND dry sludge bed are part of the sewage treatment plant. Please let me know whether we can cover these facilities or not and what is micro-biological process in these. If we can provide cover than what will be the effect on its biological..

  Type of reaction involving protonated alcohol

The reaction between 2-methyl-2-pentanol and HBr to yield 2-methyl-2-pentene is probably: A) an E1-type reaction involving the protonated alcohol as the substrate. B) an SN2-type reaction involving the protonated alcohol as the substrate.

  Compute critical buckling load for timber column of square

compute the critical buckling load for a 2.5m timber column of full size square section 0.10m x 0.10m. The column has pinned ends(k=1). Assume the modulus of elasticity is 12Gpa and that the Euler formula applies

  Formulate and solve the minimum weight design

consider the cantilever beam-mass system. formulate and solve the minimum weight design.

  Determine the average value of k in meter per sec

A stopwatch was started when h was 501 mm and read 17.6 seconds when h was 244 mm; the test was repeated for a drop from 254 mm to 97 mm and the time was 22.4 seconds.

  Determine which method of extraction should be used

Ocean water contains 0.9 ounce of gold per ton. Method A costs $220 per ton of water processed and will recover 85% of the metal. Method B costs $160 per ton of water processed and will recover e of the metal.

  Determine what manometer reading can be expected

Is this flow laminar. What is the viscosity of the oil. For the same flow in the opposite directio, what manometer reading can be expected.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd