Determine the final mixture temperature

Assignment Help Mechanical Engineering
Reference no: EM13712230

A 0.9-m3 rigid tank is divided into two equal compartments by a partition. One compartment contains Ne at 0C and 100 kPa, and the other compartment contains Ar at 50 C and 200 kPa. Now the partition is removed, and the two gases are allowed to mix. Heat is lost to the surrounding air during this process in the amount of 15 kJ. Determine (a) the final mixture temperature and (b) the final mixture pressure. Show all steps and assumptions.

Reference no: EM13712230

Questions Cloud

Flow around a model of a turbine blade is investigated : The flow around a model of a turbine blade is investigated. The model is five times larger than the prototype. A maximum pressure of 4 psi is measured at the leading edge, a maximum velocity of fps is measured near the top of the blade, and a small d..
Water filled manometer is attached to the inlet : A water filled manometer is attached to the inlet and the test section of a low speed wind tunnel which has the contraction ratio of 3. what would be the pressure difference between the inlet and the test section in terms of inches of water in order ..
How do they fit within the situational crime prevention : What are the countermeasures to those threats, and how do they fit within the Situational Crime Prevention framework - how does the current law help or hinder your countermeasures? Are there any proposals for laws that would assist?
Magnitude of force transmitted to module through isolator : An electronic control system for an automobile engine is to be mounted on top of the fender inside the engine compartment. It is desirable to isolate the module from the vibration induced in the car by road and engine vibration. Design an isolator (i..
Determine the final mixture temperature : A 0.9-m3 rigid tank is divided into two equal compartments by a partition. One compartment contains Ne at 0C and 100 kPa, and the other compartment contains Ar at 50 C and 200 kPa. Now the partition is removed, and the two gases are allowed to mix. H..
Logarithm stress versus logarithm rupture lifetime plot : Estimate the rupture lifetime (in hrs) for some cylindrical component originally 10.5 mm in diameter and 496 mm long that is fabricated from a low carbon-nickel alloy; assume that it is to be exposed to a tensile load of 6300 N at 538°C. The logarith..
Approximated with a triangular probability density function : The distribution of X is approximated with a triangular probability density function f(x) = 0.025x-0.0375 for 30
What is the optimal production schedule for this firm : What is the optimal production schedule for this firm? What is the profit contribution of each of these products and what is the marginal value of an additional hour of time on machine.
Find the thermal efficiency-net work and work ratio : A single-stage ideal regenerative steam cycle has a boiler pressure and temperature of 5000 kPa and 500 C, and a condensing pressure of 10 kPa. The extraction pressure is 500 kPa. If the regenerative heater is a closed heater with the condensate pump..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Sketch a diagrammatic pneumatic circuit for the control of

sketch a diagrammatic pneumatic circuit for the control of a double acting cylinder using a 52 valve that is

  Hydrogen gas is contained in a vertical piston-cylinder

hydrogen gas is contained in a vertical piston-cylinder device at 14.7 psia and 15 ft3. at this state a linear spring

  A light pressure vessel is made of 2024-t3 aluminum alloy

a light pressure vessel is made of 2024-t3 aluminum alloy tubing with suitable end closures. this cylinder has a 3.50

  What is the definition of the streamline and what are its

1. what are the four fundamental quantities of fluids in aerodynamics?2. what are common units used both english usgs

  Wat is the time expression for the motor response if the

the 500 lbf motor is supported on springs with a total stiffness of 5000 lbfin. the springs have a damping ratio of

  A 1500 lb crate is pulled along the around at a constant

a 1500 lb crate is pulled along the around at a constant speed for a distance of 25ft using a cable that makes an andle

  Find the initial pressure and mass of the system

Water in the pictured piston cylinder assembly has an initial quality of 10%. The piston cylinder is 20 cm in width and the piston is initially 40 cm high. Heat is added until the temperature of the steam reaches 500°C. While heat is being added the ..

  Determine the velocity ratios that can be achieved

Determine the velocity ratios that can be achieved by the gear box in terms of number of teeth in the sun wheel  and determine which component (out of the sun wheel, planet carrier and annular wheel) has to be used as the input shaft to get the req..

  Explain vector integral - stokes therom

Vector integral - stokes therom, Evaluate the line integral by stokes theorem (clock wise as seen by a person standing at the origin).

  What is the rate of entropy generation in the turbine when

what is the rate of entropy generation in the turbine when steam enters an adiabatic turbine at 8mpa and 500oc at a

  Suspended symmetrically by two strings

A uniform bar of length l and weight w is suspended symmetrically by two strings, set up the differential equation of motion for small angular oscillations of the bar about the vertical axis, and determine its period.

  An electric current of 025 a flows through a 5-ohm

an electric current of 0.25 a flows through a 5-ohm electrical resistor placed in an evacuated chamber. the resistor is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd