Determine the exit area and the exit mach number

Assignment Help Civil Engineering
Reference no: EM131036201

Steam enters a converging-diverging nozzle at 1 MPa and 500°C with a negligible velocity at a mass flow rate of 2.5 kg/s, and it exits at a pressure of 200 kPa. Assuming the flow through the nozzle to be isentropic, determine the exit area and the exit Mach number.

Reference no: EM131036201

Questions Cloud

Determine the log reduction required by chlorination : SENV 672 - WASTEWATER TREATMENT (SPRING 2016) - HOMEWORK. Determine the log reduction required by chlorination for total coliforms and Cryptosporidiumif our fine screens provide (essentially) zero pathogen removal and our MBR provides 4 log removal..
Determine the mass flow rate of air through the nozzle : determine the mass flow rate of air through the nozzle. Take the ambient conditions to be 265 K and 85 kPa.
Evaluate hr service delivery : The assessment task is due on the date specified by your assessor. Any variations to this arrangement must be approved in writing by your assessor.
Determine the initial mass flow rate of air through the leak : Assuming isentropic flow, determine the initial mass flow rate of air through the leak.
Determine the exit area and the exit mach number : Assuming the flow through the nozzle to be isentropic, determine the exit area and the exit Mach number.
Prepare the end-of-month report to account for the incomes : Prepare the end-of-month report to account for the incomes and expenses of KenKam Sign Enterprise under cash basis accounting - Prepare the end-of-month report to account for the incomes and expenses of KenKam Sign Enterprise under accrual basis a..
Determine the highest temperature that air can be heated : Determine the highest temperature that air can be heated by heat addition while the mass flow rate remains constant.
Describe each video and the social institutions it addresses : Describe each video and the social institutions it addresses. Identify any relevant models of power structure or political behavior that might be influential.
Incentive plan to fail : In your view, what might cause an incentive plan to fail? (Minimum 300 words)

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  Calculate the height of the capillary rise in the tube

A clean glass capillary tube having a diameter of .008 in. was inserted into water with a surface tension of 0.00504 lb/ft. Calculate the height of the capillary rise in the tube.

  Temporary change on the highway

Determine the minimum distance from the diversion that a road sign should be located informing drivers of the temporary change on the highway. The letter height on the road sign is 5 inches.

  Express the approximate alkalinity of the water

A water sample has bucarbonate concentration of 220 mg/l ( HCO3- )and the PH of the water is 7.9 > Express the approximate alkalinity of this water as mg/l of CaCO3

  What is the velocity of striking

If the ball strikes the side of the building 2s after being thrown, at what height above the base of the building did the ball strike the building? What is the velocity of striking?

  What is temperature of the tires of the increase pressure

A motorists inflates the tires of her car to a gauge pressure of 180 kilopascals on a day when the temperature is -8.0 degrees Celsius. When she arrives at her destination, the tire gauge pressure has increased to 245 kilopascals.

  Find what diameter pipe is required to triple the capacity

Given an 18-in. concrete conduit with a roughness coefficient of n = 0.013, s = 0.02, and a discharge capacit of 15 cfs, what diameter pipe is required to triple the capacity

  What are the basic assumptions of the traffic flow model

Two 25-kip loads are maintained 6 ft apart as they are moved slowly across the 18-ft beam ab. write a computer program and use it to calculate the bending moment under each load and at the midpoint c of the beam for values of x from 0 to 24 ft at int..

  Determine what should be the removal efficiency

The regulatory agency has told the company to maintain a salt level pf no greater then 250 mg/L downstream of the discharge. what should the removal efficiency. (percentage of the salt removed) of a process designed to remove salt from the waste w..

  Determine the angular velocity of pinion gear and velocity

The pinion gear rolls on the gear racks. If B is moving to the right at 8 ft/s and C is moving to the left at 4 ft/s, determine the angular velocity of the pinion gear and velocity of its center A.

  Find the maximum allowable tensile force

A 4-cm- diameter rod of aluminum 7075-T6 is to subjected to an axial tensile force such that the factor of safety based on the yield stress on 1.75. Find the maximum allowable tensile force. The yield stress of the aluminum 7075-T6 is o-y= 500MPa.

  Engineering ethics concepts and cases

Engineering ethics concepts and cases

  Determine the velocities and u and w and the speed of the

Determine the velocities and u and w and the speed of the flow along the streamline at (3,2). Determine the slope of the streamline in degrees from horizontal. Determine the acceleration at the point. Determine the pressure at the point (3,2) in N/m2..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd