Determine the displacement of joint

Assignment Help Electrical Engineering
Reference no: EM13869238

Problem 1: For the following truss, each member has the same EA. All members are pin connected at their joints.

(i) Under the loads at C and D, determine the displacement of joint D along the CD direction (20')

(ii) Without consideration of the loads at C and D, if the member CB is fabricated 1 inch too short, determine the horizontal displacement of joint D (20').

2333_displacement of joint D along the CD direction.jpg

Problem 2: For the following beam with EL being constant. Assume the support at A is a pin and C is roller.

(i) Determine the maximum deflection of the beam and its location (20')

(ii) Now another roller is added at B under the beam to reduce the deflection of the beam. Calculate the force at the roller B and the maximum deflection of the beam again (40')

2230_Determine the maximum deflection of the beam.jpg

Reference no: EM13869238

Questions Cloud

Applying the intermediate value theorem : Applying the intermediate value theoremSuppose f is a continuous function on [-2, 2] such that f(-2)=1, f(2)= -1?Which of the properties below follow without further restriction on f by applying the Intermediate Value Theorem?
Calculate the data rate in gb per second of herbs eyes : Each pixel is basically a superposition of five ‘‘colors'', each of which has 32 intensities. The time resolution of Herb's visual field is 10 msec. Calculate the data rate, in GB/sec, of Herb's eyes.
A material error in net income for a previous period : On January 1, 2010, Franklin Company had a retained earnings balance of $206,000. During 2010 the following events occurred:
Determine the system reliability : If both batteries are operating in parallel, they have an individual failure rate of 0.1 per year. If one fails, the other can operate the transceiver (at a reduced power output). However, the increased electrical demand will triple the failure ra..
Determine the displacement of joint : Problem 1: For the following truss, each member has the same EA. All members are pin connected at their joints. (i) Under the loads at C and D, determine the displacement of joint D along the CD direction (20')
How many pages is one toner cartridge good for : The rest is blank (i.e., no toner) The toner layer is 25 microns thick. The printer's toner cartridge measures 25 * 8 * 2 cm. How many pages is one toner cartridge good for?
Determine the binomial distribution for any random data : Determine the binomial distribution for any random data. Also determine the probability greater than 4.
Write the summary for the statistical methods : Write a few lines about the main question and design of the study and then write the summary for the statistical methods. Basically something like the abstract but the statistical section should be more detailed than the rest
Prepare a classified balance sheet or report form : Prepare a classified balance sheet (report form)

Reviews

Write a Review

 

Electrical Engineering Questions & Answers

  Determine the position x and the tension in the cord

Determine the position x and the tension in the cord that is required for equilibrium. The cord passes through the smooth ring at B and has an unstretched length of 6ft and stiffness of k = 50lb/ft.

  What component values are supposed to be used

An intercom system has a 13 kHz annoying whistle with amplitude of 20% of a typical voice signal. Assume that a typical voice signal has a frequency of 3 kHz and the intercom's output for a typical voice level has amplitude of 10V.

  Determine and compare the intrinsic impedance

Determine and compare the intrinsic impedance, attenuation constant, and skin depth of copper [σcu =5.80 × 10^7 (S/m)], silver[σag=6.15 × 10^7 (S/m)], and brass[σbr=1.59 × 10^7 (S/m)]

  Determine the power loss due to the line impedance

A balanceed three-phase load of 15 MA with a lagging load factor of 0.85 is supplied by a 115KV subtransmission line. if the line impedance is 50+j100Ohm per phase, determine the following: (a) The line current of the load

  Calculate the maximum allowable gate drive power

A thyristor is triggered by a pulse of train of 5kHz.The duty ratio of the pulse train are 0.5. If allowable average gate power is 100W, calculate the maximum allowable gate drive power.

  Basic semiconductor components: diodes

The shape of the characteristic curve for a neon lamp is the same as the shape of a characteristic curve for a diode.

  Determine what is the capacitance of the capacitor

A capacitor is formed by two metal parallel plates with thearea 5.1 um*um. The distance between plates is 4.3 um. The gap between plates is filled with the dielectric material with dielectric constant 19. What is the capacitance of this capacitor?

  Determine how much poweer is required from the source

A receiver requires 20 mW as input power. If all the system losses add up to 40 dB, then How much poweer is required from the source

  Design a logic network to control the lights of the doors

A long hallway has three doors, one at each end and one in the middle. A switch is located at each door to operate the incandescent lights along the hallway. Label the switches A,B, and C. Design a logic network to control the lights.

  Determine number of data points used by the fft algorithm

It requires the frequency resolution to be less than 0.5 Hz. Determine the number of data points used by the FFT algorithm and actual frequency resolution in Hz, assuming that the data samples are available for selecting the number of data points.

  Design a non-inverting op-amp-based amplifier with a gain

Calculate( show all details, including Input versus Output voltage curve) and indicate all circuit required circuit parameter values in order to achieve both positive and negative output bounds as specified earlier. Briefly and very clearly descri..

  What will be potential difference between plates seperation

An Air capacitor consisting of two closely spaced parallel plates has a capacitance of 1000 pF. The charge on each plate is 1 micro C. What is the potential difference between the plates. If the charge is kept constant.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd