Determine the depth of flow immediately upstream of the hump

Assignment Help Civil Engineering
Reference no: EM13545608

A rectangular channel of 2 m depth and 5 m width carries 1 m deep running water. It is laid to a slope of 0.001 with Manning’s n = 0.02. Some distance downstream there is a hump of height 0.5 m on the stream bed. Determine the depth of flow immediately upstream of the hump. Sketch the problem and the specific energy diagram

Reference no: EM13545608

Questions Cloud

Find the cumulative distribution function of the elongations : Elongation (in %) of steel plates treated with aluminium are random with probability density function
Derive a relationship to evaluate the discharge : Using Buckingham-Pi method, derive a relationship to evaluate the discharge, Q, over a rectangular notch as a function of the width of notch, b, acceleration due to gravity, g, fluid density
The circular cross section will be maintained during : A cylindrical rod of 1040 steel originally 15.2 mm (0.60 in.) in diameter is to be cold worked by drawing; the circular cross section will be maintained during deformation
Determine the normal depth of flow before and after the : Determine the normal depth of flow before and after the change in gradient. Will it be possible to produce a hydraulic jump in the channel downstream of the junction of two slopes?
Determine the depth of flow immediately upstream of the hump : A rectangular channel of 2 m depth and 5 m width carries 1 m deep running water. It is laid to a slope of 0.001 with Manning’s n = 0.02. Some distance downstream there is a hump of height 0.5 m on the stream bed
The final temperature in the tank in degrees celsius : A rigid tank whose volume is 10L is initially evacuated. A pinhole develops in the wall, and air from the surroundings at 1 bar, 25 degrees Celsius enters until the pressure in the tank becomes 1 bar.
Design the weir structure in order to accommodate the design : To avoid submergence the crest of the weir must be at least 0.05 m above the downstream water depth. Here we can assume that the depth downstream is equal to the normal depth. To simplify calculations we will assume that Cd = 0.7 Water depth over the..
Determine the pressure in the tank indicated by a strain : A single strain gage forming an angle B = 18 degrees with a horizontal plane is used to determine the gage pressure in a cylindrical steel tank. The cylindrical wall of the tank is 6mm thick, has a 600mm inside diameter
What is the function of a separation membrane between : A single strain gage is cemented to a solid 4-in diameter steel shaft at an angle B = 25 degrees with a line parallel to the axis of the shaft. Knowing that G = 11.6*10^6 psi, determine torque T indicated by a gage reading of 300*10^-6 in/in.

Reviews

Write a Review

 

Civil Engineering Questions & Answers

  How much will each leg shorten under the applied

given that E for the tube material is 70 GN/m2 and the stool legs are 75cm long, how much will each leg shorten under the applied compressive load (take g = 9.8m/s2)

  Determine height from ground and time at which may pass

Ball A is thrown vertically upward from the top of a 30-m-high building with an initial velocity of 5 m/s. At the same instant another ball B is thrown upward from the ground with an initial velocity of 20 m/s. Determine the height from the ground..

  A dam project specifies 97 compaction lab tests on the soil

a dam project specifies 97 compaction. lab tests on the soil being used indicate that it has anbspmaximum dry density

  Compute the station and elevation of the curve turning point

Set up a table showing curve elevations at the PVC, at the PVT, and at the half-station points along the curve. Compute the station and elevation of the curve turning point.

  Determine the mass of neon in a vertical cylinder

Neon gas at 50 degrees C in a vertical cylinder of diameter 150 mm has a 6 kg frictionless piston mounted. The outside pressure is 98kPa and the neon volume is 4000cm^3. Find the mass of neon.

  What is significant difference between free jets and flows

What is the most significant difference between "free" jets and flows in confined structures (nozzles, pipes, etc.) in terms of formulation of force terms ÓF(i.e. left hand side) of the momentum equation

  Estimate the bending moment at the base of the chimney

A cylindrical chimney,1 m in diameter and 2.5 m tall is exosed to a uniform 50km/hr wind at standard atmospheric conditions.End effects and gusts may be neglected.

  Calculate the angles made by f with the positive x and y

A force is specified by the vector F = [(10)i + (150)j + (-50)k] N. Calculate the angles made by F with the positive x-, y-, and z-axes

  Determine what fraction of the cyanide is in the cn- form

Cyanide solutions used for heap leaching are made up of sodium cyanide (NaCN). The sodium cyanide solution ([NaCN]-total = 0.01 M) is kept at pH 10.4. The pH is kept high to keep the cyanide in the CN- form.

  Determine the maximum in-plane shear stress on the wall

a). Determine the state of stresses in the walls and indicate these stresses (including arrows to denote the direction of the stresses) on the element below. b). Then, determine the maximum in-plane shear stress on the wall of the pipe using Mohr's..

  Determine the rankine earth pressure diagram

A ten-foot high wall will retain a medium dense sand backfill. Determine the Rankine earth pressure diagram and the total active force on the wall.

  What must the hydraulic detention time be in the aeration

Although primary and secondary sedimentation is responsible for the removal of some BOD, you will design a bioreactor which removes 85% of BOD entering the plant using an activated sludge bioreactor. Use the following values: Influent (to bioreactor)..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd