Determine the change in specific kinetic energy

Assignment Help Mechanical Engineering
Reference no: EM13712382

Steam steadily flows through a turbine to produce mechanical work. At the inlet, the pressure, temperature and velocity of the steam are 10 MPa, 450 °C and 110 m/s, respectively. The water exits this turbine at pressure of 10 kPa with the quality of 90% at velocity of 20 m/s. During this process, the rate of heat loss from the turbine to the surrounding air is 12 kW. The mass flow rate of the steam is 10 kg/s. ignoring the changes in potential energy, determine:

1) the change in specific kinetic energy, in kJ/kg

2) the power output of the turbine, in kW

3) the area of the exit port of the turbine, in m2

Reference no: EM13712382

Questions Cloud

Prepare 2015 statement of cash flows by direct method : Prepare the 2015 statement of cash flows by the direct method and how will what you learned in this problem help you evaluate an investment?
Greening new and emerging markets : Greening new and emerging markets: Defining Best Practices Due 5/8. A. Pick an existing market that's small enough to shift with localized effort ( Portland Oregon Breweries/ Beer Industry/ Sustainability).
Find what the magnitude of the initial velocity : A projectile is launched at an angle of 34.9 degrees above the horizontal and lands at the same level from which it was launched 2.07 seconds later. Find the magnitude of the initial velocity
Made of plastic with a maximum working stress : A camera case shown on the right is made of plastic with a maximum working stress of 1000 psi. What thickness of material should be used to create the case if the case will be used at 150 feet of depth in sea water?
Determine the change in specific kinetic energy : Steam steadily flows through a turbine to produce mechanical work. At the inlet, the pressure, temperature and velocity of the steam are 10 MPa, 450 °C and 110 m/s, respectively. The water exits this turbine at pressure of 10 kPa with the quality of ..
Compute the tension in the rope : A small object with mass 0.200 kg swings back and forth on the lower end of a light rope that is 3.00 m long. what is the tension in the rope
Consider two people playing an ultimatum game : 5) Consider two people playing an ultimatum game over $10 that can be divided in $1increments ($10-$0, $9-$1, $8-$2, etc.). Suppose it is common knowledge among them that both have Fehr-Schmidt utility functions with the assumptions given i..
Estimate what the magnitude of the net magnetic field : The current in a solenoid with 50 turns per centimeter is 0.44 A. The solenoid has a radius of 1.5 cm. Find the magnitude of the net magnetic field
Hydrostatic tension-hydrostatic compression : What would happen to safety of factor of brittle material under the state of Hydrostatic tension, Hydrostatic compression

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the centroidal moment of inertia

Determine the centroidal moment of inertia for the following. The center circle is cut out. you have a rectangle standing up ward the height is 7 in and the width is 4 in there is a cut out hole in the center with 2 in for diameter.

  Determine the actual exit temperature for the compressor

A given mass flow rate (.17 kg/min) of an ideal gas flows through an adiabatic compressor operating at steady state. The compressor has an adiabatic efficiency of N(%) = 87.5. The gas has a molecular weight of MW = 28.5 (kg/kmol) and a specific heat ..

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

  You may treat the sphere as a particle and neglect the mass

a bullet of mass m0 is fired horizontally with a velocity v0 into the slender bar of a pendulum of mass m and length l

  Sigma x sigma y 80 bar sigma zz 100 bar tau xy tau

the following stress state exists around a wellbore drilled in the atlantic oceansigma x sigma y 80 bar sigma zz

  If the actual flow rate consumed by the motor is 0005 m3s

a hydraulic motor has a displacement of 130 cm3 and operates with a pressure of 105 bars and a speed of 2000 rpm. if

  Calculate the brake kw of the fan if its efficiency is 65

a centrifugal fan is to be used to take a flue gas at rest zero velocity and at a temperature of 352.6 k and a pressure

  Describe possible methods that can be used to separate

describe possible methods that can be used to separate materials such as polymers, aluminium alloys and steels from one another.

  Calculate the velocity at the exit of the nossels

The stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically. Air enters a set of these nossels at 270 psia and 795 F with a velocity of 97 ft/s and exists at 200 psia and 550 F. Calculate the..

  Completely drill out the crack with hole

A long rectangular bar 20 mm wide and 10 mm thick made of hot-rolled 4340 carbon steel (Sy = 860 MPa, K1c = 99 MPaÖm), is found to have a centrically located through-thickness crack 8mm wide. Is it best to a) leave the crack alone, b) drill a 5 mm di..

  Describe the basics of the carnot cycle of thermodynamics

describe the basics of the carnot cycle of thermodynamics and its application to heat engines such as diesel engines

  A piston cylinder containing ar at some initial

a piston cylinder containing ar at some initial temperatureto is allowed to cool. once the volume of the cylinder

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd