Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
An 8×1 MUX has inputs A, B, and C connected to the selection inputs S2, S1, and S0, respectively. The data inputs I0 through I7 are wired as follows: I0 = I1 = 0, I2 = I6 = , I3 = I5 = I7 = 1; and I4 = D. (a) Determine the Boolean function that the MUX implements. (b) Implement the function using a 4×1 MUX with minimum extra logic gates.
An AISI 4140 OQT 1000 sleeve is to be secured to a 2.50-inch diameter solid rod ot the same material employing a class FN1 force fit. The outside diameter of the sleeve is 5.00 inches.
A two-resistor voltage divider consists of a 10 k and a 15 k ohm resistor, with the 10 k resistor connected to the voltage source and the 15 k resistor connected to ground. If the output voltage is 2.5 V across the 10 k resistor
A measurement signal has a frequency less than 1 kHz, but there is unwanted noise at about 1 MHz. Design a low-pass filter that attenuates the noise to 1%. What is the effect on the measurement signal at its maximum of 1 kHz
Japan has both a 50 Hz power system and a 60 Hz power system. A motor - generator set is designed to connect the two. The basis is that the motor would be operated from the 50 Hz system and on a common shaft
Calculate the probability that the system will fail in 3,000 hours. Supposing no failure of any component occurs in 5,000 hours of operation. What would be your revised estimate of failure rates of the components in your system?
In a Zigbee network, Coordinators and Routers can't "sleep", i.e. enter a low-power, inactive mode. Why is this What implications are there because of this on the structure and applications of a Zigbee network
An Electrical System is rated 10kVA, 200V at a .5 leading the power factor. a. determine the impedance of the system in rectangular coordinates. b. find the average power delivered to the system
In a motor control system, one master stop pushbutton (Stop) is available for stopping the operation at any time. If the temperature switch (TSW) is closed, pressing the red pushbutton (RedPB) will turn on both motors M1 and M2.
A dc series motor of 230 V, 12 hp, 1200 rpm is connected to a 230 V supply. It draws a current of 40 A, and rotates at 1200 rpm. Ra = 0.25 ohms and Rs = 0.1 ohms. Assume magnetic linearity.
To discharge a capacitor of 1mF charged with a voltage of 1 volt we connect it, at time t=0, with a resistor of R-ohm. When we measure the voltage in the resistor we find it to be v_R (t)=e^(-t) u(t). Determine the resistance R.
The average noise power per unit bandwidth measured at the front end of an AM receiver is 10^(-3) watt per Hertz. The modulating wave is sinusoidal, with a carrier power of 80 kilowatts, and a sideband power of 10 kilowatts per sideband.
General questions for network communications, A user message is split into 15 frames, each of which has an 80% chance of arriving error-free. If no error control is used by the data link layer, how many times must the message be sent on the averag..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd