Determine the average normal stress at the critical section

Assignment Help Civil Engineering
Reference no: EM13315194

two 10 mm thick steel plates are fastened together by means of two 20mm bolts that fit tightly into the holes. if the joint transmits a tensile force of 45 kn determine

a.) the average normal stress in the plates at a section where no holes occur

b.) the average normal stress at the critical section

c.) average shearing stress in the bolts

d.) average bearing stress between the bolts and the plates

Reference no: EM13315194

Questions Cloud

Determine what is the acceleration of diatomic oxygen gas : 2 kilomoles of diatomic oxygen gas are enclosed in a 10-kg steel container. A force of 2kN now accelerates this system. What is the acceleration
What does the slope of the linear line : A graph of the Force applied to a spring and the distance it stretches F vs. x yields some valuable information. What does the slope of the linear line
Calculate what is the force required at a constant rate : A 20-kg iron ball is moving at 100 km/hr should be accelerated at a constant rate of 10 m/(sec)^2. What is the force required
Hat is the direction of the net electrical field : Consider two particles, each with a charge of +Q located at the opposite corners of a square of side d. What is the direction of the net electrical field at point P
Determine the average normal stress at the critical section : two 10 mm thick steel plates are fastened together by means of two 20mm bolts that fit tightly into the holes. if the joint transmits a tensile force of 45 kn determine the average normal stress in the plates at a section where no holes occur
How to decrement the ttl field of the packet : In addition to the above-mentioned  KeyboardInterrupt (used to terminate the program), you will need to handle any I/O-related exceptions.
Determine the magnitude and location of the resultant force : The tank contains water to depth of 2m and oil (SG=0.8) on top of the water to a depth of 1m. Determine the magnitude and location of the resultant force acting on one end of the tank (i.e. 3m high by 3m wide).
Determine by trigonometry corresponding magnitude of r : Knowing that the magnitude of P is 35 N, determine by trigonometry (a) the required angle a if the resultant R of the two forces applied to the support is to be horizontal, (b) the corresponding magnitude of R.
What are the predominant types of bond in each category : what are the three meterials based on the predominant types of bond and what are the predominant types of bond in each category

Reviews

Write a Review

Civil Engineering Questions & Answers

  How many resistors out of package of 100 to burn up

A 6.6 mA current is flowing through a 47 kilo-Ohm, 5% tolerance, 2-watt resistor. If the resistor values are uniformly distributed, how many resistors out of a package of 100 would you expect to burn up

  Determine how much pressure is developed in the system

A multiple-piston hydraulic jack has two output pistons, each with an area of 250 cm^2. The input piston, whose area is 25 cm^2, is concerned to a lever that has a mechanical advantage of 9:1.

  Define materials to construct an industrial building

Materials To Construct An Industrial Building, A small building can be constructed of steel or wood framing. A decision is made to use steel for fire resistance.

  Calculate the number of gas transfer units

The gas flow rate is 1 kg m-2 s-1 of and the water entering is 1.6 kg m-2 s-1. For this system Henry's law holds and ye=1.75x, where ye is the mol fraction of A in the vapour in equilibrium with a mole fraction of x in the liquid.

  Estimate the settlement of 10-ft and 5-ft square footings

Footings for a structure are to be built beneath a basement slab on a clay soil at a depth of 20ft below present ground level. The groundwater table is 15 ft below the ground surface. The soil-void ratio is about 0.87.

  Determine the speed of the car at o at constant speed

A car traveling over a hill at constant speed starts to lose contact with the ground at O. If the radius of curvature of the hill is 85 m, determine the speed of the car at O.

  Ddetermine the tension of each cable above the incline

two cars, connected by a cable, are winched up an incline using a second cable. the incline makes an angle of 25 degrees with the horizontal, and the winch rises another 30 degrees above the incline.

  Determine the optimal amount of space rays and zappers

Galaxy Industries is a manufacturing company that produces two toy doll models: the Space Ray and the Zapper. The Space Ray can be sold for a profit of $8/dozen and a profit of $5 can be made if a dozen of Zappers are sold.

  Design a suitable pavement consisting of a granular subbase

if the subgrade has a resilient modulus of 103,500kN/m2, design a suitable pavement consisting of a granular subbase with a layer of coefficient of 0.13, a granular base layer with a layer coefficient of 0.14, and an asphalt concrete surface with ..

  Define the front of our library has six double doors

the front of our library has six double doors and the doors rotate open in the middle making less clerance room how can i get started

  Define coil spring which has been compressed

Question about Spring, A 37kg object is placed onto a coil spring which has been compressed 43mm. The force used to compress the spring was 35KN.

  What is time-mean speed and space-mean speed for vehicle

assume you are an observer standing at a point on the track for a period of 30 minutes and are recording the instantaneous speed of each vehicle as it crosses your point. what is the time-mean speed and space-mean speed for these vehicles for this..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd